Notifications
Clear all

Help!!!

32 Posts
7 Users
0 Reactions
17.3 K Views
Posts: 110
Topic starter
(@brant78)
Estimable Member
Joined: 10 years ago
[#47429]

This is my first year running blinky flashy and I can’t get the lights on.
I am running a Renard SS24 with Vixen 3.4
The show will run on the scheduler and I can see my preview going and the music is coming through on the radio but, my lights on the house are not coming on at all.
I only have 23 channels and a real simple set up but, with this being my first year I just want this to work! Lol. Thank you for your help!

Brant

Sent from my iPhone using Tapatalk


31 Replies
Posts: 555
(@zaker)
Honorable Member
Joined: 19 years ago

You have a USB to RS485 adapter correct, not connected to an Ethernet port?

Check your baud rate, default Renard baud rate is 57600

Did it work when you tested it? Or did you setup and hope for the best? :w00t:


Reply
Posts: 142
(@mt2525)
Estimable Member
Joined: 14 years ago

Go into your Vixen setup page and right click on your renard controller and make sure you configured it to the right COM port. You can determine your correct COM port by going into your device manager on your computer.


Reply
Posts: 110
Topic starter
(@brant78)
Estimable Member
Joined: 10 years ago
zaker wrote:You have a USB to RS485 adapter correct, not connected to an Ethernet port?

Check your baud rate, default Renard baud rate is 57600

Did it work when you tested it? Or did you setup and hope for the best? :w00t:

I have the usb to RS485. Connected according to the wiki info. White/Orange and orange are ground and plugged into 1 and 2 and white blue is positive and blue is negative on the 4 and 5 on the RJ45 with the flat part facing up.

Baud Rate is 57600

I did not test. ☹️ I bought the controller from another board member and figured it worked.

Sent from my iPhone using Tapatalk


Reply
Posts: 110
Topic starter
(@brant78)
Estimable Member
Joined: 10 years ago
mt2525 wrote:Go into your Vixen setup page and right click on your renard controller and make sure you configured it to the right COM port. You can determine your correct COM port by going into your device manager on your computer.

It automatically picked it when I opened Vixen after plugging it in. It’s a gearmo and the red and green lights are on

Sent from my iPhone using Tapatalk


Reply
Posts: 110
Topic starter
(@brant78)
Estimable Member
Joined: 10 years ago

So the proper lights on the rs485 are coming on and it looks like the data is sending but I have zero Leds lit on the controller itself.


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

Are there any lights flashing on the SS24? Did you create the cable per instructions in the wiki?

Note: only the first RS45 to SS24 needs this cable.

Wiki   DMX (RJ 45) to Renard SS Connection

Reply
Posts: 110
Topic starter
(@brant78)
Estimable Member
Joined: 10 years ago
algerdes wrote:Are there any lights flashing on the SS24? Did you create the cable per instructions in the wiki?

There are no lights flashing on the board. The only light on is the power light.
I did create the cable correctly.

Sent from my iPhone using Tapatalk


Reply
Leglamp
Posts: 438
(@leglamp)
Honorable Member
Joined: 14 years ago

If the led lights on your renard are not illuminated, check the fuse and make sure the power wire is actually inserted in terminal. Is the power wire coming off your renard controller terminated with a vampire connector? If it is check the vampire connector and make sure the little teeth pierced the wire casing.

Brant78 wrote:So the proper lights on the rs485 are coming on and it looks like the data is sending but I have zero Leds lit on the controller itself.

Reply
Posts: 110
Topic starter
(@brant78)
Estimable Member
Joined: 10 years ago
algerdes wrote:Are there any lights flashing on the SS24? Did you create the cable per instructions in the wiki?

Note: only the first RS45 to SS24 needs this cable.

I’m wired directly to my computer usb via RS485

Sent from my iPhone using Tapatalk


Reply
Page 1 / 4
Share: