Multiple Routers Se...
 
Notifications
Clear all

Multiple Routers Setup Issue?

3 Posts
2 Users
0 Reactions
1,421 Views
Posts: 33
Topic starter
(@sdkraemer)
Trusted Member
Joined: 8 years ago
[#49846]

I'm trying to setup FPP for my dad. His setup is simple, a raspberry pi connected to a F4V3 controller.

He has a router that is connected to a modem. Then he has a second router that is connected directly to his first router. The second router is what the pi is connected to.

I setup a different show network, then added a route on his computer so he could access the falcon controller from a browser, but it doesn't seem to be working. It appears to me that the router tries to connect to the other router, which doesn't know about the pi or the falcon controller.

Here is how I set everything up:

FPP:
He has 'Channel Outputs' E1.31 enabled and using eth0.
wlan0:
IP Address: 192.168.2.137
Netmask: 255.255.255.0
Gateway: 192.168.2.1
https://drive.google.com/open?id=1eynqEr7QHu7knTU24ZBRMYiXqVX_gajs
eth0:
IP Address: 192.168.3.100
Netmask: 255.255.255.0
Gateway:
https://drive.google.com/open?id=1SQ-KDKI4cNO5GGHF87Y39tqzZdsRvxen
Falcon F4V3:
IP Address: 192.168.3.101
Mask: 255.255.255.0
Gateway: 192.168.3.100
DNS: 192.168.2.1
https://drive.google.com/open?id=1CgFcP2K4dNy3q7pANNn3OH49UZlIyuxO

Diagnostics:

IP Config:
https://drive.google.com/open?id=1akj76QSSFPMEHRSOIK2FdkOLvG1sy1er

Route print:
https://drive.google.com/open?id=1KPs0_-rgUXTZ5nWWINfXHIKPP5berZ4J

Tracert to falcon controller:
192.168.2.1 is the gateway that showed up in ipconfig, so I used that. The router.asus.com is the router connected to the modem.
https://drive.google.com/open?id=1iFgH0oG_Gjz_xaH7mPqA33_t8BQz3N2p

Tracert to eth0 IP Address:
https://drive.google.com/open?id=13s2ezbaZYeieA5DujVzCL6p6hcG8_egL

Tracert wan0 IP Address:
Looks fine to me.
https://drive.google.com/open?id=1LAGgQTx0kaN-Eg-0iUI8LEgtJ3VOIzKx

I'm not sure if its the fact that there are two default gateways listed in ipconfig. The persistent route of 0.0.0.0 also looks odd in the 'print route' command. I deleted it and now my dad can't reach the internet, so I have to figure out how to re-add it.

Any ideas are much appreciated, thanks!


2 Replies
Posts: 33
Topic starter
(@sdkraemer)
Trusted Member
Joined: 8 years ago

Actually, so I deleted that odd persistent route 0.0.0.0 and I seemed to fix the problem.

Sent from my ONEPLUS A6003 using Tapatalk


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago

What is the 10.0.1.1 Gateway in your IP config?

You connected the show router's WAN/Internet port to a LAN port on the primary Router, correct? Where is the Show Router located? If you can, connect your father's PC to it, at least temporarily to get things configured.

Can you connect to the Pi via the WiFi network? Are you using its IP address? http://192.168.2.137

On the Pi, Did you enable routing between Network Interfaces? Bottom of the Network Config page.


Reply
Share: