Wireless Controller...
 
Notifications
Clear all

Wireless Controller for LED costumes

15 Posts
9 Users
0 Reactions
10.5 K Views
Posts: 4
 Eyad
Topic starter
(@eyad)
Active Member
Joined: 14 years ago
[#37245]

Dear Team,

I've created LED costumes using WS2811 LEDs and each costumes has 500-600 LEDs and want to control them wirelessly to sync them with music and I use lipo batteries to power the suite and controller.

What is the best mobile (should be worn by the person wearing suite) wireless DMX controller (TX & RX) or other type of controller i can use to drive the effects on the LED costume that will be synched with the music.

I'm looking for a controller that will allow me to individually control the pixels within my costume.

Thanks in advance for your support and advise


14 Replies
Posts: 366
(@technician)
Reputable Member
Joined: 12 years ago

1 Avoid baseband DMX as your LED Pixels are not DMX. This rules out some of the DMX XLR solutions. Use a variety of pixel controller instead.
2 Best resources to search are groups already doing wireless group costumes. Might try to contact these guys.

3 Due to power, bulk, range, reliability, wireless might not be the best option. Your pixels can be driven from a Falcon Player on each costume, each with it's own sequence. Only requirement for sync is a common time reference for all the player clocks just prior to the show. This can be as simple as simple as plugging in network cables into a home router long enough to get the time on boot up.

I do the reverse when recording video. A separate recorder is used for the audio instead of a wireless mic. The two or more audio and video sources are placed in sync in post production. The start of the video uses a clap board, just like the big films and for the same reason. The event common to all video and sound is used for alignment of all tracks on the timeline. Playback is the same in reverse. All sequences for all actors is in sync on the sequencer. The individual actors sequences are clipped and exported to the Pi Players. The Pi Players clocks are synchronized with the Network Time Protocol.

This should then be able to run a reliable show without the hazards of congested WIFi. Slaving Pi Players is an option, but then it is still subject to lost packets over WiFi.

These people seem to be in the business of doing this. They would be good to ask. http://led-clothing.com/led-costumes.html


Reply
Posts: 2229
(@plasmadrive)
Famed Member
Joined: 15 years ago

I did a wireless LED pixel jacket last year to wear around when helping with traffic. I had it synchorized to the rest of my show. I used Komby wireless to drive the pixels directly. The only issue I had was that because it used an Arduino there was a slight delay compared to the rest of the show. I assume it was the Arduino because wireless was plenty fast.. but I did have delay. Anyway, it worked several hundred feet away.


Reply
Posts: 4
 Eyad
Topic starter
(@eyad)
Active Member
Joined: 14 years ago

Thanks @Technician for your detailed answers, however, i'm still new in this field so not sure if i understood you correctly.

The challenge is that we have to make the synch between the audio and LED effects real time during the live show. as of today we do the synch manually by recording the LED effects animation on SD card and play it with the controller through a button controlled by the dancers. however, any delay from any of the dancer in starting the sequence will damage the show.

I agree with you that wireless controllers have risks .. but it can be mitigated if the show environment studied well (Distortion ,etc..).

I'm looking for wireless solution so i can create different interactive experiences by hacking it and try to integrate it with Touch Designer or Processing to try and make new effects and experiences. and to be able to control the trigger of LED effects real time.

Technician wrote:1 Avoid baseband DMX as your LED Pixels are not DMX. This rules out some of the DMX XLR solutions. Use a variety of pixel controller instead.
2 Best resources to search are groups already doing wireless group costumes. Might try to contact these guys.

3 Due to power, bulk, range, reliability, wireless might not be the best option. Your pixels can be driven from a Falcon Player on each costume, each with it's own sequence. Only requirement for sync is a common time reference for all the player clocks just prior to the show. This can be as simple as simple as plugging in network cables into a home router long enough to get the time on boot up.

I do the reverse when recording video. A separate recorder is used for the audio instead of a wireless mic. The two or more audio and video sources are placed in sync in post production. The start of the video uses a clap board, just like the big films and for the same reason. The event common to all video and sound is used for alignment of all tracks on the timeline. Playback is the same in reverse. All sequences for all actors is in sync on the sequencer. The individual actors sequences are clipped and exported to the Pi Players. The Pi Players clocks are synchronized with the Network Time Protocol.

This should then be able to run a reliable show without the hazards of congested WIFi. Slaving Pi Players is an option, but then it is still subject to lost packets over WiFi.

These people seem to be in the business of doing this. They would be good to ask. http://led-clothing.com/led-costumes.html


Reply
Posts: 4
 Eyad
Topic starter
(@eyad)
Active Member
Joined: 14 years ago
plasmadrive wrote:I did a wireless LED pixel jacket last year to wear around when helping with traffic. I had it synchorized to the rest of my show. I used Komby wireless to drive the pixels directly. The only issue I had was that because it used an Arduino there was a slight delay compared to the rest of the show. I assume it was the Arduino because wireless was plenty fast.. but I did have delay. Anyway, it worked several hundred feet away.

Thanks @plasmadrive , What software did you use on the PC side and Hardware TX ? also on the jacket what were the LED chipset and Which Komby Wireless Hardware ? and what was the role of the arduino ?


Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago
plasmadrive wrote:The only issue I had was that because it used an Arduino there was a slight delay compared to the rest of the show. I assume it was the Arduino because wireless was plenty fast.. but I did have delay. Anyway, it worked several hundred feet away.

For both the 2013 and 2014 shows I used an Arduino, Ethernet Shield and a Minimalist Shield (aka "Komby Sandwich") and never showed any lag. I know plenty of others who had the same configuration and nobody has ever mentioned a lag.

For the OP, I did run a battery-driven set of LEDs on the bench to test out how long batteries would last for a remote prop I wanted to build ... this was a dumb LED setup with 48 lamps and a pack of eight AA lith ion batteries ... I was able to run a five-hour show without running out of power, but only got an hour into a second night. Changing batteries every day would have been impractical for this prop, so I gave it up.

HTH.

\dmc


Reply
hasoon
Posts: 520
(@hasoon)
Honorable Member
Joined: 15 years ago

I am currently working on a similar project for my son's haloween costume. My first plan was for me to carry a laptop and broadcast to him via a Kombee Sandwich. Now I have changed my mind and am planning to use a Raspberry pi and FPP. I won't have as much control but should be able to connect to the pi wireless with my smartphone to control things. I'm hoping a pair of 5000mah 2C lipos in series into a buck converter will run him for several hours (if not I have 4 total)


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago
Eyad wrote:Dear Team,

I've created LED costumes using WS2811 LEDs and each costumes has 500-600 LEDs and want to control them wirelessly to sync them with music and I use lipo batteries to power the suite and controller.

What is the best mobile (should be worn by the person wearing suite) wireless DMX controller (TX & RX) or other type of controller i can use to drive the effects on the LED costume that will be synched with the music.

I'm looking for a controller that will allow me to individually control the pixels within my costume.

Thanks in advance for your support and advise

What kind of location will the dancers be in?

Would it be feasible to use Wifi?(This should be a separate locked down network from anything else in the area)

I think you might want to look in to using a Falcon Player and E6804 Pixel Controller on each dancer. Run the Falcon Player in "slave" mode on the dancers and have a "master" off body to keep them all in time. The Falcon Player has an ethernet port to connect to the E6804 and you would have to add a USB wifi adapter to connect the slaves to the master.

600 pixels is 1,800 channels or just over 3.5 universes.


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

Wouldn't an ESPixelstick fit the bill perfectly for this?
I am amazed it hasn't been suggested....


Reply
Wolfie
Posts: 2225
(@wolfie)
Noble Member
Joined: 11 years ago

Well, since the thread was originally from 2015, that doesn't surprise me at all.


Reply
Page 1 / 2
Share: