Last season I ran into some issues with my dumb pixels flickering. Some people said it was dmx issues while others thought it might be voltage drop. I honestly never completely solved the issue since the "show" was always on going and by the time I got home from work...well it was time to start up the "show".
If you take a look at this;
Go to about the 2:30 mark and look at the mini trees in the front. The trees are split with 2 of the 27 ch. RGB controllers. 8 trees for one and 8 trees for another. I have 35 RGB nodes on the tree and 50 RGB nodes on the extension for each channel.
For power I have a Astron 35M ( http://www.hamradio.com/detail.cfm?pid=H0-004436OPEN ) that is rated 35 amps surge and 25 amps continuous. The line going out to the controllers is long. About 60 to 70ft but had at least 6 gauge wire going out to it. If memory serves me right it would never drop below 12.5v on full white...if it dropped that much.
For dmx signal I had a Sandevice controller running my "Flextech" arches right there at the apex of the extensions...so came off it with a dmx line (out of one of the ports).
As a school teacher, summer time is the time for me to acquire "stuff" and build. While there are a couple of pre-sales going on, I thought I might pick up some power supplies if this would solve my problem...if the group thought. Too expensive of a power supply (and too dog gone heavy!) to water proof it for out door use. Or if it looks like flaky dmx signals.... I may have to re-think the setup for this year.
2 more days of post planning...and then let the building begin 😉
Thanks for your suggestions,
Robert
Fayetteville, GA
www.burtonchristmaslights.weebly.com
1st off, the display is awesome and I never would have picked up on the flickering if you hadn't pointed it out... 😉
If I am reading your description correctly, it looks like you have 85 RGB nodes off one RGB channel. Looking at standard RGB nodes I believe they consume .3watts each, so 85 X .3 = 25.5 watts. Power is equal to voltage X current, so 25.5 watts using 12v as voltage results in 2.125 amps of current. I know that the 27 channel DMX controller is rated for 1 amp/channel or 15amps total if no mod is done. I have completed the mod on my boards and beefed up the tracks to get 2 amps/channel but never push it that much except for maybe one or 2 full RGB strips on an input. I would say your issue is overloading the board if it is in stock mode. I have pics of the traces you have to beef up and can reply with them when I get home if you want.
I doubt very seriously that you have a flicker of that type due to power issues. That looks much more like a data issue. Check to see that you have a terminator at the end of your DMX data string. Also, sometimes a terminator at the flickering board can help... other times it can make it worse. I have no idea what type of cable you are using or how you have it connected, but if you used Cat5 you may have moisture issues with the cable. (just throwing stuff out there that it could be). If you don't have a data ground wire tying them together you may be exceeding the differential voltage that the receivers can handle with respect to common. (it does happen, though not usually in our type of displays). If you are using CAT5 cable you may just try another pair in the cable. If you are using single pair twisted shielded cable, make sure the shield is tied in where it should be.
BTW, is that flicker in the same spot every time? If so it may be in your program somewhere... (again, just a thought). If it is random that would not be the case.
Yeah that looks like data to me as well, at higher data rates like DMX uses you get and echo of the data back down the line thats what the termination resistor does it removes that echo my having the lowest impedance in the data line so it forces most of the power to return down the gnd line.
Edit: More info.
Thanks for the replies.
Dr Neutron - (Txns 😉 I have done the mods on each board. Really wish those mosfets were turned the other way so they could be heat sinked. I toyed with the idea of putting a small metal rod thru each hole to give it some metal for heat sinking. Be interesting to find some that are rated at 2amps. But that would be a heck of lot of de-soldering and soldering back 🙁
I think the question was asked if it happened in the same place each time...and no not really. It is close but not exactly in the same spot.
plasmadrive - I am using Cat5. *I Think* I tied the pairs together??? Have slept since then and would have to go and check. I do need to pull out all those cables and check though...to see how I wired it.
kingofkya - I did have a termination resistor at the end of the lines. If memory serves me right....it didn't seem to make a difference. However.... trying a different pair as mentioned above might work. I do remember talking with the gentleman over at Sandevices about this. He did mention about the data ground being tied together and pretty sure I did that.
Will go and watch the vid though. Looks interesting....and it's ham talking about coax??? Cool. Did not know you could turn a o-scope into a TDR. Need to look at some stuff here at the house and on my repeater! ( http://disneycrazy.smugmug.com/gallery/7943953_gF4Q3#!i=517182384&k=rkqRw5c ) May have to replace my db420 at the top of that tower! Uggghh! More money away from my lights 😉
Got to run do a net. (selinkedrepeater.net) Come check us out on KI4NGD-R at 9pm est.
73
Robert
KD4YDC
If you are using Cat5 you should use only ONE pair for D+ and D- per universe. Don't tie any pairs together for the data signals. You can take a second pair and tie those two wires together and use that as a common.
That is what I have done 🙂
RobertB wrote:Thanks for the replies.
Dr Neutron - (Txns 😉 I have done the mods on each board. Really wish those mosfets were turned the other way so they could be heat sinked. I toyed with the idea of putting a small metal rod thru each hole to give it some metal for heat sinking. Be interesting to find some that are rated at 2amps. But that would be a heck of lot of de-soldering and soldering back 🙁
I think the question was asked if it happened in the same place each time...and no not really. It is close but not exactly in the same spot.plasmadrive - I am using Cat5. *I Think* I tied the pairs together??? Have slept since then and would have to go and check. I do need to pull out all those cables and check though...to see how I wired it.
kingofkya - I did have a termination resistor at the end of the lines. If memory serves me right....it didn't seem to make a difference. However.... trying a different pair as mentioned above might work. I do remember talking with the gentleman over at Sandevices about this. He did mention about the data ground being tied together and pretty sure I did that.
Will go and watch the vid though. Looks interesting....and it's ham talking about coax??? Cool. Did not know you could turn a o-scope into a TDR. Need to look at some stuff here at the house and on my repeater! ( http://disneycrazy.smugmug.com/gallery/7943953_gF4Q3#!i=517182384&k=rkqRw5c ) May have to replace my db420 at the top of that tower! Uggghh! More money away from my lights 😉
Got to run do a net. (selinkedrepeater.net) Come check us out on KI4NGD-R at 9pm est.
73
Robert
KD4YDC
Instead of trying to replace parts and build on something that was not designed to support that high of current have you looked at the Ren24DC? Supports 2A/Channel easy and up to 4A/Channel when heat sinks are used. Board maxes out at 60A, giving 30A per side for 12 channel banks.
RobertB wrote:That is what I have done 🙂
If this is the case, then I would play with terminator resistors. You should only have one at the end but sometimes it works better with one on each. Make sure the common wire it good all the way thru.
Moisture could still be an issue if the Cat5 jacket was not water proof and it got soaked. May not be your issue, but it does happen.
Plasmadrive - I will give that a try. Trying to think back to Nov / Dec, I honestly think I tried "Jerry Rigging" some resistors on both ends. I probably need to just go buy some rj-45's (is that the right number for the connector?) and crimp in a resistor...the correct way 😉
dlovely - That is an idea. If I knew then what I know now...might have gone that route. I would just wonder though if it was that or not. I was looking at something else this morning on a different video this morning
and you will notice the flicker even more (sequencing not as good...from earlier years ;-).
I would think if it were power issues, because of the fades and full on... it would happen more. Fingers crossed it is just signal loss.
