Enttec USB + 3ch De...
 
Notifications
Clear all

Enttec USB + 3ch Decoder = Random Blinking?

25 Posts
3 Users
0 Reactions
8,163 Views
Posts: 128
Topic starter
(@vadoo)
Estimable Member
Joined: 19 years ago
[#41993]

I've been away from the blinky flashy hobby for a couple years. I hope to get back to it this year but I'm basically starting over with all new sequences, software, and some new hardware.

(Links below) I'm going from Vixen 2 to Vixen 3. I'm adding (hopefully) an Enttec USB Widget (1) connected at the moment to a single 3ch DMX Decoder (2).

So far all I get is random on/off of different colors on a test RGB string.

I've tried Vixen 2 and 3 on Win 10 and Vixen 2 on Win 7. I have the drivers from Enttec installed. From the Enttec to the decoder have have pin 1 to G, pin 2 to D-, pin 3 to D+. I set up Vixen 3 to use DMX Pro port 3 @ 57600 Baud, Parity none, Data Bit 8, Stop Bit 1. Flipping the test switch (dip 10) on gives the expected output on the lights.

I'm not sure what I'm doing wrong. I thought I had a good understanding of what I needed. Any suggestions?

Links:
(1) http://www.enttec.com/?main_menu=Products&pn=70302
(2) http://www.aliexpress.com/item/2016-Best-price-1-pcs-DMX-3CH-BAN-V1-3CH-Channel-DMX-512-LED-Decoder-Controller/32491962291.html?spm=2114.13010608.0.84.iJtPHN


24 Replies
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago

Not sure how it is done in Vixen 3 but this is how you do it in Vixen 2.

In regards to baud rate, DMX uses a much faster and non-standard speed but I suspect the FTDI driver would ignore your settings in favor of the correct ones.


Reply
paudyd
Posts: 140
(@paudyd)
Estimable Member
Joined: 13 years ago

Make sure your running Enttec OPEN driver and not just the Enttec or Enttec pro. The "open" uses the pc to constantly update the communication.

Sent from S6 using Tapatalk


Reply
paudyd
Posts: 140
(@paudyd)
Estimable Member
Joined: 13 years ago

BTW, the link you attached is for the Open version. They are fine for testing but I would suggest HolidayCoro's for a show. Or better yet a e1.31 controller. IMHO

Sent from S6 using Tapatalk


Reply
Posts: 128
Topic starter
(@vadoo)
Estimable Member
Joined: 19 years ago

Thanks for the replies. I started over using the steps you suggested. This is the same way I set it up to start, but it doesn't hurt to try again. I went as far as uninstalling/reinstalling the drivers. The best results so far are from Vixen 2, using Enttec Open DMX and the DMX add in. I tried to take, and upload a video but wasn't successful (size/format issues), So I'll try to explain exactly what is happening. For better clarity of whats going on I switched to a 30ch decoder with built in leds. Over the course of about 6 seconds, the activity light flickers erratically but not steadily. The upper channels, maybe 22-30, are lit. The rest of the lights begin to flicker on in order from highest ch # to lowest until they are all on. The all stay on for a few seconds during which time the activity light completely stops. Then the cycle starts over again.


Reply
Page 1 / 5
Share: