DMX analyzer
 
Notifications
Clear all

DMX analyzer

9 Posts
6 Users
0 Reactions
8,991 Views
Posts: 447
Topic starter
(@blackbeard)
Honorable Member
Joined: 18 years ago
[#5262]

Can anyone recommend a freeware, DIY DMX analyzer? I've seen some pretty neat ones on the web, some with LCD output, .. things like that.

Thanks for any info


8 Replies
Posts: 386
 JEC
(@jec)
Reputable Member
Joined: 19 years ago

I looked around for something as well. Couldn't find any that were stable and workable. Ended up building a small hardware box which receives DMX and transmits serial to a computer @ 115,200 baud.

Outputs data to Hyperterminal using some VT100 escape characters, so the on-screen display is neat and tidy. I think I ended up with about a 10 Hz screen refresh rate.


Reply
NogginBoink
Posts: 482
(@nogginboink)
Honorable Member
Joined: 19 years ago

JEC, would you want to share that project? It sounds like something many of us could benefit from.


Reply
Posts: 386
 JEC
(@jec)
Reputable Member
Joined: 19 years ago

Sure - I could write something up. The board is the same one used in the 18F4550 'Offset Machine - Pixel Driver Board' project.

There's a picture included in post #13 here:

http://www.doityourselfchristmas.com/forums/showthread.php?t=2879

When I designed the board, I included a set of pins for serial debugging.

Et Voila!


Reply
Posts: 447
Topic starter
(@blackbeard)
Honorable Member
Joined: 18 years ago

Appreciate the replies. As usual, I find there are some stuff already in the "DMX Projects" sticky in this section of DMX here. I meant no disrepect for the people who made those projects, I just had not found them yet as I familiarize myself with the forum.


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

How about something like this? http://www.elektor.com/magazines/2002/june/portable-dmx-tester.55709.lynkx

I built one a while ago. the main reason I chose this was the battery operation.

I has a couple of modes of read write.

PM if you want more details.
Matt

PS,
I found the Artwork I did to make a single sided PWB if you want to make your own.


Reply
Posts: 22
(@henne)
Eminent Member
Joined: 18 years ago

@matt:
Can you post a quick overview of the features of the elektor analyzer? (There might be some features, I forgot in my own analyzer fw ;))

Thanks,
hendrik


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

Below is straight for the original article:

Table 1. Specifications for the Portable DMX Tester
– Portable tester with modest dimensions
– Compatible with DMX512-1990
– Transmitted and received data visible on an LCD
– Very straightforward operation (5 buttons)
– Operates from rechargeable battery or mains adapter
– Two functions: DMX transmit and receive
– Transmits on 512 DMX channels (480 are adjustable, the others remain 0)
– Start Code during transmission can be adjusted as desired
– Receipt of 480 channels, the values of which are indicated from 0 to 255
– Indication of the received Start Code
– Indication of received data, so that a break in the cable can be detected immediately
– The option of storing the received DMX-values in the memory of the tester and re-transmit
them again at a later time


Reply
Posts: 12
(@snarfer)
Active Member
Joined: 19 years ago

Well I would like some RDM features. It would be really cool to have a portable device that could be used to set starting address and other parameters for RDM fixtures. In fact if I can't find a project that does that I am going to have to make one myself.

Actually I think the way you have set up the case and everything for the "pocket size" DMX analyzer is very good. It looks quite professional.

There is a commercial device with these features: Artistic License Jump-Start Portable DMX RDM Tester.

Also if it had a usb port so it could double as a usb-dmx/rdm adapter that would be interesting. And if you could use it for uploading firmware.


Reply
Share: