WS2801 controllers
 
Notifications
Clear all

WS2801 controllers

36 Posts
14 Users
0 Reactions
31.5 K Views
mrpackethead
Posts: 2289
(@mrpackethead)
Famed Member
Joined: 19 years ago
LabRat wrote:Aren't your pixels powered by these same chips? If so.. doesn't that mean these same limitations would/should apply?

Yes, they are, and yes they are subject to the same law.


Reply
mrpackethead
Posts: 2289
(@mrpackethead)
Famed Member
Joined: 19 years ago
dmoore wrote:I wonder if World Semi is on a "watch list". If so, then it makes it more useful if they are shipped in via one of the many resellers that are not on a watch list.

I'm not sure if WS is, but product containing their chips has been

MPH - have you had any of your units/chip orders seized?

No


Reply
Posts: 42
(@riri7707)
Eminent Member
Joined: 17 years ago

As patent and royalty seems to be the main PB, there are a lot of tips and tricks to overpass these difficulty, especially for personnal use, like ours in the forums.

1st tip : scratch the ref on component and have them sent from third party...

Simple, as the size box of 1000 units is very small and can be shipped in the middle of pcbs, connectors, etc.... Can be packet and labelled as prototypes...

A lot of simple ideas, but not for commercial use, of course....:)

Cheers... Henri


Reply
Posts: 604
(@aussiephil)
Honorable Member
Joined: 19 years ago

Matt

Very interesting.... the 422 may not be needed.

For everyone looking at using the 2801 or other similar chips we are about to release a high end pixel controller.

Here's the details

TigerPB-TP3212

The Tiger Protocol Bridge (TigerPB) TP3212 is a small controller for use with RGB LED lights and LED strips that utilise driver chips like the 6803/2801/3005. These are the currently targeted protocols and it is possible that other 2-wire and single wire protocols could be supported with firmware upgrades. This will provide future proofing of your controller.

The initial release will accept a standard DMX512A data stream and provide control for 170 RGB Pixels (510ch). There will be dual buffered outputs that will allow you to split the 170 pixels into say 100/70 and run them in different directions and yet control them as a single 170 pixel string.
Each dual buffered output will also allow for the parallel connection of the same number of pixels allowing for two strings to be used with the same patterns. If these are run in opposite directions they would provide for mirrored effects.
Each of the Dual outputs will be able to drive different protocols if required.

Whilst the controller board will have normal type jumpers to allow for option setting or protocol selection, to allow for fully waterproof sealed use all settings will be able to be made via alternate start code DMX data. Also planned is full Remote Device Management (RDM) support.

The RS485 input is optically isolated to protect the controller. Power supply required is either 5V or 12V. This allows the controller to be used with both RGB Pixel Strings or RGB Pixels without having to worry about additional power cabling.

Features announced as of August 10.

DMX512A input
Individual control of up to 170 RGB Pixels as one string. Uses up to 510 DMX channels
Two separate buffered outputs allows for splitting of strings and independent control of a total of 170 RGB Pixels Uses up to 510ch
Strings can be split based on the requirements of the user, for example 68 RGB Pixels on one output and 102 on the other. Controller is then update remotely via software
The two outputs can be treated as parallel outputs with both strings displaying the same sequence, still only uses up to 510ch
Each of the two separate outputs has is own parallel secondary output. This can be used to duplicate each string output if desired
Multiple Protocol support built in with 6803, 2801 supported from the release date, 3005 support is planned but not yet tested
Output 1 and Output 2 can be different protocols at the same time, increasing the flexibility for your display
Basic configuration is available via jumpers on board, however to access the advanced features remote software management will be provided
RDM will also be included in a later firmware release
16Mb of on board memory is supplied, standalone use with inbuilt RGB Effects will be supported as well as triggering of those effects via DMX control (Note: not in initial firmware and will be released in the future)
User selectable grouping of RGB Pixels is supported allowing for as few as 3 DMX channels to control an entire string as one lights, note that the number of groups should evenly divide the total RGB Pixels used
Ambient light sensor support is included allowing for the controller to know when it is dark and turn on you connected strings
PCB is 84mm x 39mm, the small size allows the end user to explore various mounting and weather proofing options


Reply
mrpackethead
Posts: 2289
(@mrpackethead)
Famed Member
Joined: 19 years ago

For those that are interested we released our Pixel controller ( completely ope source ) a few weeks ago..

Details at www.response-box.com/rgb.

Heres the details

The T3open is a small controller for use with RGB LED lights and LED strips that utilise driver chips like the 6803 and the 2801. These are the currently targeted protocols and it is possible that other 2-wire and single wire protocols could be supported with firmware upgrades. This will provide future proofing of this desgin.

The current software accepts a standard DMX512A data stream and provide control for 170 RGB Pixels (510ch). There are four indivual outputs buffered outputs that will allow you to put any combination of strings/pixels on those strings ( provided they add up to no more than 170 in total )
All of the outputs coudl have different sorts of pixels on it.

The RS485 input is optically isolated to protect the controller. Power supply required is either 5V, however you can happily run 12 or 24V led strings if you need. This allows the controller to be used with both RGB Pixel Strings or RGB Pixels without having to worry about additional power cabling.

PCB is $10, or make your own.. Parts run to about $15.. And available now. And we hope we will see lots of software variations..

Update: has been running well for several months, now.. this was demonstrated at the Melbourne Mini for the Aussies. The 'open' is the baby brother to our T3-Pro


Reply
Page 6 / 8
Share: