WS2801 and LED/ICAN...
 
Notifications
Clear all

WS2801 and LED/ICAN strings

17 Posts
5 Users
0 Reactions
7,910 Views
Posts: 183
Topic starter
(@buckanear)
Estimable Member
Joined: 15 years ago
[#20374]

Not sure if this has been done before or not, but the other night I started looking at the WS2801 spec sheet and saw something that might very well do what I want.

The concept is to put the WS2801 in constant voltage mode with an external switch.

Sounds interesting and why I never grasped the beauty of this mode before I do not have a clue. I have been in a search for simple means of doing both LED and INCAN strings with only one board and one software. So I think I have found my solution after several months.

So how does it work?

Well the WS2801 can source up to 50mA in constant voltage mode. The external switching transistor can switch the increased current for high current LEDs like the Cree XLamp series. Along comes the ON Semi NSI450xx series of Constant Current Regulators and I think my dream has come true. So now I can increase not only the current but the voltage also. The idea is for the WS2801 outputs to drive a MOSFET (BS107A), and a string of either LEDs or ICAN lights. The string can be anywhere from 3 to about 50 lights with an AC input of 12VAC to 120VAC input. The idea is to use a bridge rectifier and a simple capacitor filter to generate the voltage. With 120VAC that will be about 169VDC. With a load current of about 500mA, three channels at 150mA per channel and 50mA overhead, the capacitor need be only about 330uF to give enough filtering to keep the ripple to less than 20V peak to peak. Te valley of the ripple needs to be about 5 volts above the total forward voltage of the string. The ripple voltage is dropped across the CCR. An AC voltage will actually help to reduce heat dissipation for the CCR.

The idea is to rectify the AC line voltage and filter with a single cap. For INCAN light string of 35 or 50 lights the volt will be about 125 V across the series string. These will have a NSI45090JD CCR in a DPAK case. This can be adjusted for a constant current of 90 to 160mA. The other end of the string will be switched with a BS107A FET that has an open drain voltage of 200 volts and a peak current of 500mA. With about 6.5 Ohms of on resistance the FET will drop about 1 volt across the drain source junction. The WS2801 output will drive the gate of the FET, thus allowing the whole string to be dimmed at 256 levels. No zero crossing detection, no phase dimming. Straight PWM dimming.

The WS2801 is to be driven from a DMX to Pixel bridge that RPM has already completed. Now each string is essentially a pixel. The WS2801 draws power off the rectified AC input. I now have a schematic and a PCB layout done with EXPRESSPCB.

Plans are to next week send out for prototype and see what happens. A couple of things that will need addressing for final release is protection for the WS2801 should the FET fail. Also the fact that the data transfer between boards at 2MHz is limited to 6 meter(~18 feet). The later can be solved with an on board driver to increase separation and increase the transfer speed. That will come with the next pass.

Like I said this can also work on 12VAC from the low voltage lights that are so common. With setup the Cree MLE Xlamps could be used used and run at 125 to 150 mA current. Three of those in series can produce a nice flood or used in a luminary.

just been thinking and hope I have something that will do what I want.

james


16 Replies
David_AVD
Posts: 991
(@david-avd)
Noble Member
Joined: 17 years ago

PDF versions of the files will let many more people see (and comment on) your work.


Reply
jrock64
Posts: 1099
(@jrock64)
Noble Member
Joined: 19 years ago

Interested in your design, but...
not Express PCB
or Eagle

convert to PDF or capture as jpeg

Joel


Reply
Posts: 183
Topic starter
(@buckanear)
Estimable Member
Joined: 15 years ago
jrock64 wrote:Interested in your design, but...
not Express PCB
or Eagle

convert to PDF or capture as jpeg

Joel

Joel

Let me find away to convert the PCB layout to PDF and I will.

I did it with ExpressPCB to get a fast turn around. Most of the low cost places like BatchPCB and Seeedstudio take almost a month. I want to experiment with something sooner and not later. I can redo the circuit easily in Eagle when the concept is proven.

james


Reply
Posts: 183
Topic starter
(@buckanear)
Estimable Member
Joined: 15 years ago

Okay

here is a PDF of the schematic.

One note is this is really very crude prototype and some of the values have yet to be determined or yet finalized. The value of C1 is probably not the final value. It more than likely will increase to around 330uF or more. My SPICE runs have a 330uF and I still maintain 135VDC at the valley of the ripple. More than adequate for the CCR. I can add a two stage PFC to help the valley more or just increase the cap value.

The zener cap value is still undetermined. The WS2801 spec states that the overhead current for the logic is 1.5mA max. Add in any current that the outputs use to that. I need to finish a few more things but so far this looks promising.

james


Reply
Page 1 / 4
Share: