What size drill bit...
 
Notifications
Clear all

What size drill bits for PCB work

9 Posts
7 Users
0 Reactions
11.3 K Views
glaforce
Posts: 414
Topic starter
(@glaforce)
Honorable Member
Joined: 17 years ago
[#18969]

What size of drill bits do i need to get for making PCB's? Is there a fairly basic few bits i will need? I'm going to drilling a few Simple Renard 32 PCB out and what to use the right size of bits.

Gary


8 Replies
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

You need little ones. Wire drills. I've bought a lot from widgetsupply.com -- and they actually last quite a long time, yet they're super-cheap. You get ten bits in a little tube for about $3.

You'll need different sizes, so check the pads on your PCB layout to find out the sizes of the holes. Then order appropriate bits.

Here's a link to widgetsupply's dremel bit page...

http://www.widgetsupply.com/page/WS/CTGY/dremel-drill-bit-wire-gauge


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

If you're going to use a drill press, make sure it will actually hold the bit. My little Sears press couldn't tighten down on the real little ones (I think #72 or so) but my new Jet has no problem. A dremel type press probably won't have an issue. Drilling is the only reason I don't make more of my own boards - ugh...


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
budude wrote:A dremel type press probably won't have an issue. Drilling is the only reason I don't make more of my own boards - ugh...

I leave the toner on the board after etching because it aids as sort of a drill guide. It allows me to hand-hold the Dremel and zip, done! I don't remove the toner until just before I'm ready to build the board, too, and the toner prevents the copper traces from oxydizing from the open air. I've had boards that I etched 2 or 3 years ago and finally decided to build, removed the toner and the copper is nice and clean!


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

These work?
I thought HSS bits dulled instantly for this work and that you needed to buy the carbide drills.

dirknerkle wrote:You need little ones. Wire drills. I've bought a lot from widgetsupply.com -- and they actually last quite a long time, yet they're super-cheap. You get ten bits in a little tube for about $3.

You'll need different sizes, so check the pads on your PCB layout to find out the sizes of the holes. Then order appropriate bits.

Here's a link to widgetsupply's dremel bit page...

http://www.widgetsupply.com/page/WS/CTGY/dremel-drill-bit-wire-gauge


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
ukewarrior wrote:These work?
I thought HSS bits dulled instantly for this work and that you needed to buy the carbide drills.

Yep. Oh they do dull after a while, but I've drilled a couple hundred holes with a single bit, and they're so cheap, you can just throw them out.


Reply
mrpackethead
Posts: 2289
(@mrpackethead)
Famed Member
Joined: 19 years ago

0.6, 0.7, 0.8, 1.0, 1.2, 1.5, 2.0, 2.5, 3.0 and 4.0 mm would cover you for almost everything. You'll need to use a drill press for the small ones, or you'll just break them.


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

For home made board I have pretty much standardised on 0.8, 1.2 and 3.2mm dia. Every thing gets drilled out at 0.8 first. I then step out to the larger drills where needed.
Carbide is good but I break them too quickly. They as very intolerant of any lateral movement with drilling. I found I was getting ready to move to the next hole too soon. :hmm:
On a drill press you use the highest speed selection.


Reply
tstraub
Posts: 525
(@tstraub)
Honorable Member
Joined: 18 years ago

I use these drill bits.. They will get dull and break after a few hundred holes but they work well enough for me. They are cheap and I have a store right down the road from my work.


Reply
Share: