RGB Amplifier
 
Notifications
Clear all

RGB Amplifier

14 Posts
4 Users
0 Reactions
18.2 K Views
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago

It's hard to tell what your diagram is meant to represent, in particular what the yellow and black lines are supposed to represent, nor have you specified which MOSFETs that you intend to use (there are a number of different varieties). In any case, I think that the optocouplers that you've selected will be too slow. In addition, I think that additional components are needed to ensure that both the optos and the MOSFETs turn off (and turn off cleanly). Note, however, that I don't visit this board more often than once every few months or so. Wayne James, Martin Mueller (I think) and Macrosill can send me an email if you want more info about this topic.


Reply
Posts: 409
Topic starter
(@dim-bulb)
Reputable Member
Joined: 9 years ago
P. Short wrote:It's hard to tell what your diagram is meant to represent, in particular what the yellow and black lines are supposed to represent, nor have you specified which MOSFETs that you intend to use (there are a number of different varieties). In any case, I think that the optocouplers that you've selected will be too slow. In addition, I think that additional components are needed to ensure that both the optos and the MOSFETs turn off (and turn off cleanly). Note, however, that I don't visit this board more often than once every few months or so. Wayne James, Martin Mueller (I think) and Macrosill can send me an email if you want more info about this topic.

The black and yellow is the power and ground. .The upper right pin on the optocouplers should be grounded as well, but forgot to add that in. these are the Mosfets and these are the optocouplers.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago

I'm under the impression that you want this device to drive dumb RGB LED strings, similar to the parts in the section 'Dumb RGB Products' on the diyledexpress web storefront, but I don't know what you would be using as the signal source for 'this device'. In particular, are you sure that both ground and power are available from whatever is driving this device (or would be driving the LED string if this device is absent)? The reason that I ask is that when I designed a Renard controller for dumb RGB strings a number of years ago I only included +5V (or +12V, depending on what was required by the LED string) on the output connector and there wasn't any ground signal.

Never mind, I now think that there is a separate power supply that is independent of whatever would be used as the signal input.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago

I'm going to see if I can get one of my mothballed XP systems up and running so that I can create a readable schematic of what I think the circuit should be.


Reply
Posts: 409
Topic starter
(@dim-bulb)
Reputable Member
Joined: 9 years ago
P. Short wrote:I'm under the impression that you want this device to drive dumb RGB LED strings, similar to the parts in the section 'Dumb RGB Products' on the diyledexpress web storefront, but I don't know what you would be using as the signal source for 'this device'. In particular, are you sure that both ground and power are available from whatever is driving this device (or would be driving the LED string if this device is absent)? The reason that I ask is that when I designed a Renard controller for dumb RGB strings a number of years ago I only included +5V (or +12V, depending on what was required by the LED string) on the output connector and there wasn't any ground signal.

Never mind, I now think that there is a separate power supply that is independent of whatever would be used as the signal input.

No, this is an rgb amplifier, there is already a controller drvijng the lights, b ut this will amplify the signal so you can run more then 100 lights per controller. Unlike smart pixels that just need power injection, the dumb nodes signal operates off the ground wires. When you ask for a certain color, that wire gets a ground signal that ground signal signals the opto to turn on which in turn grounds out the mosfet that turns on the next string of lights.


Reply
Page 2 / 3
Share: