Propeller Dimmer sc...
 
Notifications
Clear all

Propeller Dimmer schematic review

66 Posts
6 Users
0 Reactions
24.1 K Views
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago
P. Short wrote:In any case, don't change the schematic yet...the numbers need to be firmed up first.

Let me know if there is anything more you need from me.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

With what I think are the latest set of parts (3FD312, W005, 4700 uF/16V cap, and any of the regulators) I think that the circuit will work fine. There may be some drooping on the 5V supply at temperatures below freezing, but I don't think that this would cause any operational problems. A lot of LCDs may start to have problems in this temperature range, and some of the LCDs that are rated for sub-freezing temperatures may require a negative voltage on the contrast pin.

The biggest issues that I see with these parts is the size and cost of the capacitor, and (maybe) some issues at below-freezing temps. I don't know if these would be real issues for you or not. If they are an issue, then we can continue this discussion.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Incidently, I would tend to stick with the LM2937 regulator from your earlier schematics. Its current output rating is adequate for the application, and its dropout voltage decreases as the temperature decreases (where the decreased capacitance of aluminum electrolytics makes a lower dropout voltage desirable).


Reply
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago
P. Short wrote:A lot of LCDs may start to have problems in this temperature range, and some of the LCDs that are rated for sub-freezing temperatures may require a negative voltage on the contrast pin.

The biggest issues that I see with these parts is the size and cost of the capacitor, and (maybe) some issues at below-freezing temps. I don't know if these would be real issues for you or not. If they are an issue, then we can continue this discussion.

I really think this needs to run below-freezing.

To that end I found a display that should work, Mouser p/n 763-0208BZ-FL-YBW. I also went through the design to see if anything else would have an issue with below-freezing temps. The 75176 and the Ethernet modules won't operate well below 0. For the 75176 I can substitute a 65176 which then drops it to -40C.


Reply
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago
P. Short wrote:Incidently, I would tend to stick with the LM2937 regulator from your earlier schematics. Its current output rating is adequate for the application, and its dropout voltage decreases as the temperature decreases (where the decreased capacitance of aluminum electrolytics makes a lower dropout voltage desirable).

Even with the an Ethernet module (additional 267mA) and an another 32 channels of dimmer control (4 - 4094s /w supporting circuitry)?


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago
DynamoBen wrote:Even with the an Ethernet module (additional 267mA) and an another 32 channels of dimmer control (4 - 4094s /w supporting circuitry)?

At those levels the original transformer would be overloaded...


Reply
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago
P. Short wrote:At those levels the original transformer would be overloaded...

As usual you are correct I need around 600mA. I could upgrade to a PL10-12-130B.


Reply
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago

With the larger size transformer what needs to change? Further are there items I need to address for the sub-freezing temps?


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

That transformer is over-kill if all you need is 0.60A, since it is rated for 1.6A at 6.3V.

In any case, what are your objectives? My belief is that you are looking to support 64 SSR channels (thus 0.4A @ 5V) and the Ethernet module (0.267A @ 3.3V), plus miscellaneous logic (including the Prop and the DC-DC converter).

For a transformer, the 3FD-412 looks nice (a little less expensive than the one that you listed). The bridge rectifier is OK. At the moment I think that the input for 3.3V regulator should not go through the 5V regulator so that the power dissipation is more evenly divided, but this depends on the Ethernet module running off 3.3V rather than 5V. In addition, I'd defer for a little bit the decision whether to power the DC-DC converter from 3.3V or 5V, using the criteria of evenly dividing the linear regulator power dissipation.


Reply
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago
P. Short wrote:
...what are your objectives? My belief is that you are looking to support 64 SSR channels (thus 0.4A @ 5V) and the Ethernet module (0.267A @ 3.3V), plus miscellaneous logic (including the Prop and the DC-DC converter).

All at sub-freezing temps.

For a transformer, the 3FD-412 looks nice (a little less expensive than the one that you listed). The bridge rectifier is OK. At the moment I think that the input for 3.3V regulator should not go through the 5V regulator so that the power dissipation is more evenly divided, but this depends on the Ethernet module running off 3.3V rather than 5V. In addition, I'd defer for a little bit the decision whether to power the DC-DC converter from 3.3V or 5V, using the criteria of evenly dividing the linear regulator power dissipation.

I've moved the 3.3V regulator to draw directly from the transformer, which has been changed to 3FD-412. The Ethernet modules do indeed draw from the 3.3V rail.


Reply
Page 4 / 7
Share: