So do you have a separate power pack for each string of lights? If so, wouldn't it make more sense to plug the power pack into a high voltage SSR?
I'm afraid I still don't have a clear picture of the requirements for lighting down under.
mmm, and what happens when you stick and inductive load ( ie a transformer ) on the output of the ssr.. You'll need to add some kind of snubber network to the output..
However, the whole point, was to get rid of any high voltage, at any part of the system, which was 'home' build. In NZ and Australia, its actually 'technically' illegal if you don't do this. Reducing to low voltage, makes some pretty significant reductions in component count as well, and it all remains safe.
So it's okay to plug the power pack into a wall outlet, but not into an SSR?
You guys have some weird laws!
Actually, I'd love to be able to design a perfect solution. But I'm not sure where the parts reduction would come. If both AC and DC loads have to be switched and dimmed, and the input needs to tolerate 12-48V AC/DC, I think these requirements would actually increase the parts count.
In any case... a switching power supply that could accept 12-48V AC/DC can be done. I lack the skills to design an output circuit that would be able to switch and dim 12-48V AC or DC loads.
NogginBoink wrote:So it's okay to plug the power pack into a wall outlet, but not into an SSR?
read what i wrote carefully.. I asked the question of you, what happens when a transformer is plugged into an ssr.. It does not act like almost resistive load of a light bulb. Its now a complex load that has significant inductive component.. You'll run into all sorts of issues ( and potentially smoke ) if you don't design your output appropriately...
You guys have some weird laws!
The law does not preclude you from putting transformers into 'ssrs'. The law precludes the use of system which are over 50V ( ac or dc ) for 'garden' or 'festival' lighting unless you are a registered electrician, and even then you need to comply with a whole bunch of rules. Its simply about safety. You really need to read the reg book to get the whole thing, because theres heaps of exceptions and special rules.
Actually, I'd love to be able to design a perfect solution.
Well, you simply wont.
But I'm not sure where the parts reduction would come. If both AC and DC loads have to be switched and dimmed,
Mmm.. let me think.. Theres nothing that i want to control that won't work on DC.. So, i don't need to control AC.. That must be your requirement
and the input needs to tolerate 12-48V AC/DC,
Um.. i don't need to support an AC input.. Thats your requirement
I think these requirements would actually increase the parts count.
Thats because your trying to merge everyone requirments into one kind of 'super-board' that will do everything for everyone... suggestion.. just build somethign that works for you, and if others find it useful, thats a bonus.
In any case... a switching power supply that could accept 12-48V AC/DC can be done.
N.S.S. But why build a seperate power supply stage, and then a seperate dimmer stage.. Why not make them the same thing.. you simply don't need to have to things doing the same task..
I lack the skills to design an output circuit that would be able to switch and dim 12-48V AC or DC loads.
Yet your contemplating a design for a system that runs at high voltage AC??
Lets just clarify one statement above
"The law does not preclude you from putting transformers into 'ssrs'. The law precludes the use of system which are over 50V ( ac or dc ) for 'garden' or 'festival' lighting unless you are a registered electrician, and even then you need to comply with a whole bunch of rules. Its simply about safety. You really need to read the reg book to get the whole thing, because theres heaps of exceptions and special rules."
-----------------
The law does not preclude the use of external 240v AC but the fixed cabling components MUST be done by a appropriately licensed electrician.
If you have the electrician installs an external 240v Power outlet you may plug in any device that has an attached plug.
I have a number of rope light fixtures for external use that are 240v.
Nothing stopping you running 1000 extension leads apart from the stupidity of doing so 🙂
Interesting that the electronics magazines continue to publish 240v mains swithing devices that are legal as they both plug into the wall socket and provide socketed outlets, therefore there is no fixed wiring involved.
Low voltage fixed wiring used in garden lights etc can be installed by a home handy man as long as the transformer can be plugged in. I seem to recall this is different if the transformer is attached to fixed wiring not a power point.
Now to christmas lights - as they have plug in transformers they would not be considered fixed wiring and being low voltage they fall into the handyman area.
The huge grey area is when we cut off the transformers and have a fixed wiring type setup at a low voltage.
I fully agree it is about safety. ALL power feeds/supplies should be appropriately fused at the SOURCE
For NB - the biggest requirement is to get rid of the potentially hundreds of power packs hence the need to have low voltage switching.
A Phil
My build is all connected to wall sockets.. ( its a big one though 32A CForm connectors ) I have a big ex telecom exchange power supply which provides me with 100A @ 48VDC.. ( which used to be hard wired in, but now has a plug on the end....
From that 48VDC supply, everything gets feed.. i strong strongly suggest a solid set of DC circuit breakers to go with it... you don't want 100A+ melting things!!
I think i'm all legal!!
This has these advantages.
** There is no mains potential on any of the equipment at all. ( 48VDC will hurt, it won't kill ), and there is no mains to run around the garden etc.
** As aussiephil so correctly states, theres no pesky little transformers, multi-boxes and the likes..
** SSR design can become very simple in deed.
