Finally Affortable ...
 
Notifications
Clear all

Finally Affortable Snowfall Tubes (FAST)

448 Posts
68 Users
0 Reactions
263.2 K Views
Posts: 691
(@stormyblade)
Honorable Member
Joined: 12 years ago

These are excellent answers - I was concerned with the spacing, but it seems that isn't as much of an issue as I thought. How do you guys actually hang the tubes? I bought the end caps off diyledexpress.com and I figured I'd run the 2-wire power wire through the loop on the tube caps and hang them under the eaves with small screw-in J hooks so I can just sit the power wire in them. The connection from the power wire to the tubes would be done with some CAT5 wires as the tubes don't draw much current no matter which program you end up using, right? How do you guys splice in the wires from the tubes to the power wires? My thought was to scrape off a little insulation, wrap the CAT5 wire around the power wire and then seal with electrical tape.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

I run the wires under the cap. And yes I scrap away the insulation and solder the pigtail to it. Then liquid electrical tape. Then seal it up with silicone. I just use shingle clips to hold the wire and tube.


Reply
Posts: 19
(@samckitt)
Eminent Member
Joined: 10 years ago

I tried to read through this, but couldnt do it all. Are these still available? Are the chips pre-programmed, or do I have to do that part? And lastly, would like to put them in my C7 strings, has anyone found an E12 screw base with built in transformer down to 5v to power these?

Thanks,
Scot


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

I'm not sure off hand if the boards and less are available. For power I think most people just used a wall wart that put out 5vdc. I used a small meanwell style switching power supply. They come programmed but you could alter the programming if desired. I think the boards came from DiyLedExpress.

Sent from my SM-G930V using Tapatalk


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

Yes, the boards came from diyledexpress. He has stock on the boards. You would need to source your own parts as they show out of stock. And program the pic yourself or find someone to do it. He also shows the super flex leds available. You may want to email them to see if they can put together some parts kits. I just got done putting mine up. No more trips on the roof till everything comes down.

Sent from my SM-G930V using Tapatalk


Reply
Posts: 691
(@stormyblade)
Honorable Member
Joined: 12 years ago

Hey, it's been a couple years since I built my FAST tubes and they are still going strong. I was asked, however, if I could build FAST tubes for Halloween, just for some added color. Now, the question is, what changes, if any, do you need to make to the resistor values, if you use different colors than the white that the Wiki calls for?

https://www.doityourselfchristmas.com/wiki/index.php?title=FAST_Finally_Affordable_Snowfall_Tube From the BOM section: "In addition, you will need up to 56 White Piranha Style Super flux LEDs. Other colors could be used, but you may need to adjust the resistor values on the controller board." In my case, I was asked to do green, amber(orange), and purple -- all using Piranha Super flux LEDs. Is there some calculations I need to know about to see if I have to change the resistors?


Reply
chelmuth
Posts: 1077
Topic starter
(@chelmuth)
Noble Member
Joined: 16 years ago

http://led.linear1.org/1led.wiz

This is a calculator for led resistor values just plug in the forward voltage for the led and the source of 5v and bam. If you were wanting to use multiple colors on a single tube I would just use the highest resistor calculated the other colors will be dimmer but most likely not noticeable.


Reply
dlovely
Posts: 3167
(@dlovely)
Famed Member
Joined: 17 years ago
chelmuth wrote: http://led.linear1.org/1led.wiz

This is a calculator for led resistor values just plug in the forward voltage for the led and the source of 5v and bam. If you were wanting to use multiple colors on a single tube I would just use the highest resistor calculated the other colors will be dimmer but most likely not noticeable.

WOOOOOAH! Welcome back!! Previous post was "10-02-2015, 07:31 AM"!!!


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

Shhhhhhhh. ................ you might scare him away again .......... lol, good to see you back!

Sent from my SM-G930V using Tapatalk


Reply
Posts: 1
(@linomax)
New Member
Joined: 9 years ago

Impressive !!!
Very good!


Reply
Page 44 / 45
Share: