Eagle and panelizat...
 
Notifications
Clear all

Eagle and panelization Help ?

20 Posts
11 Users
0 Reactions
7,570 Views
ukewarrior
Posts: 4674
Topic starter
(@ukewarrior)
Illustrious Member
Joined: 18 years ago
[#18871]

I have a small board that is done in EAGLE. 2" square about.

Does anyone know how I can put this in a panel of like boards to save money?

Can someone also point me to a fab house where I would get a good price on a paneled board.
I'm more concerned about price than speed.

I'd even welcome someone putting this in a panel for me.


19 Replies
Posts: 24
(@kipk12)
Eminent Member
Joined: 18 years ago
ukewarrior wrote:I have a small board that is done in EAGLE. 2" square about.

Does anyone know how I can put this in a panel of like boards to save money?

Can someone also point me to a fab house where I would get a good price on a paneled board.
I'm more concerned about price than speed.

I'd even welcome someone putting this in a panel for me.

Although I don't have any experience with them, I would suggest BatchPCB


Reply
ebrady
Posts: 670
(@ebrady)
Prominent Member
Joined: 17 years ago

When I have needed a large number of boards in the past, I used Gold Phoenix, which is the PCB supplier used by BatchPCB. $110 would gets you 155 sq inches. (So for a 2 inch board, you would get at least 75 boards, assuming 1 oz copper, 2 layers). I have done this a couple of times now, quality has been good.

I recently placed my first order with SeeedStudio, I have not received the boards yet so I can not testify to their quality. 10 - 2" square boards (50mm x 50mm) runs about $10.


Reply
Posts: 844
(@ags0000)
Noble Member
Joined: 16 years ago

+1 on SeeedStudio. I had boards in under 10 days (using expedited shipping), price was great, they worked first time, and they even sent extra boards at no cost (and they do the panelizing for you).


Reply
Posts: 12
(@wpafan)
Active Member
Joined: 15 years ago

Ive been looking for the same answer.. I figured out how to copy the layout to the same panel, but all the part numbers change


Reply
ukewarrior
Posts: 4674
Topic starter
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

So, the next question is: how do I get gerbers out of Eagle?


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

There are scripts available (BatchPCB had one, SeeedStudio has one) that will select the layers desired for the Gerbers. You run the script, and have the output.
Check Seeedstudio's "How to Submit", the details are listed there.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

If you use the script be sure to double check the output with a Gerber viewer (like GerbView). When I used DorkBot for some prototypes they provided a script as well but none of the part names/numbers showed up on the top layer silk. I had to change some layers around to get it to work.


Reply
ebrady
Posts: 670
(@ebrady)
Prominent Member
Joined: 17 years ago

Sparkfun has a good tutorial which shows how to go from an Eagle layout file to Gerbers. The script they reference, (sfe-gerb274x.cam) works with BatchPCB.
http://www.sparkfun.com/tutorials/109

You would pretty much follow the same steps with SeeedStudio but need to use their script instead. Here is a a tutorial someone wrote for them. http://www.lucadentella.it/2011/10/22/guida-al-servizio-fusion-pcb-di-seeedstudio/?lang=en


Reply
ukewarrior
Posts: 4674
Topic starter
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

This is great help....

THANKS


Reply
Page 1 / 2
Share: