Ever since MrLights2000 started this thread in the old forums last year, I've been intruiged by the idea of building a 'colortube' light display. The thread links to this device, which is basically a translucent tube with tri-color LED's inside it every inch or so.
It would be a very simple circuit: a '595 chain, and each output of the '595 would turn a LED on or off. You could get 7 colors per LED: off, r, g, b, rg, rb, gb, rgb. (In reality I'd probably use an Allegro 6279 in place of the '595 since it has current management integrated with one resistor.)
The problem I see with this idea is building a suitable power supply, and getting power to the boards effeciently. Get 100 or so LEDs working (that'd be only 33 tri-color LEDs showing white which would be less than 3 feet at one LED per inch), each drawing .02A, and we're up to 2 amps of current draw really quick, and voltage drop in the power supply line becomes a serious issue.
My point with this post is to just throw the thought out there and fish for ideas. How would you deliver power to the boards? What other thoughts or comments do you have?
You stole my idea. 😉 Actually you didn't but it was something I had on my sketchpad. My idea was a little different. I was going to illuminate a frosted tube at its base, not its entire length. The base would contain 3 MR16s (Red, Blue, Green) and dimming would occur locally and of course it would be DMX.
My simplified idea came from a post on the propeller site. The prop project is a lot like the Chauvet link you posted. Enjoy.
Here is the video:
Here is the thread, for an in-depth description of how it was done:
http://forums.parallax.com/forums/default.aspx?f=25&m=236431
BTW The reason I was going to use MR16s over LEDs is because I can change out the colors to Cyan, Magenta, and Yellow which would allow me to do pastel colors...and it would be brighter.
There are lots of inexpensive power supplies available, and all you need to do is use heavier gauge wiring from the p/s. You find slightly different wire resistance tables and calculators, but as an example 20AWG wire has a resistance of about 0.0119 Ohm/Foot. The voltage drop in this wire at 3 feet is pretty small, and so this general approach can work.
--
Phil
The Chauvet's aren't extremely bright so a more translucent tube would be needed. If implemented in a display I think this would be a cool border......
(For the record, Chauvet is a great company, i have used/seen all their products at one point or another :))
I guess I need to include the MR16s are brighter, with outdoor ambient light you need all the help you can get.
The tubes I had planned were 4" in diameter and where going to be 6' tall. I was going to make 4-8 of them and stand them up. Its still in the planning stages.
I played with this some last night and was a little disappointed.
I got some RGB LED's from eBay and hooked them up to a breadboard. I found that the colors don't mix very well. The R, G, and B are all distinct point light sources indise the LED case, and they project light in different directions. Even putting a translucent drinking cup over the LED didn't help... I could see the individual light pools of red, green, and blue without much mixing of colors.
Has anyone had different experiences with different LEDs? I may go ahead and prototype one board, but I'm not very confident that this is going to be a viable project, for both this reason and the reason Ben gave: the wimpy LEDs will be competing not only with ambient light, but with other lights in the display (minis, C7's) that give off much more light.
That's where you messed up. RGB LED's are not the answer. In commercial lighting like I use in the Light Jocky industry, we use separate red, green, and blue LED's bent on their PCB so they will shine in the same place. RGB LED's are actually never used in the LED products worth buying for something like a Light Tube, Cube, Sphere, wash, etc...
NogginBoink wrote:I played with this some last night and was a little disappointed.I got some RGB LED's from eBay and hooked them up to a breadboard. I found that the colors don't mix very well. The R, G, and B are all distinct point light sources indise the LED case, and they project light in different directions. Even putting a translucent drinking cup over the LED didn't help... I could see the individual light pools of red, green, and blue without much mixing of colors.
Has anyone had different experiences with different LEDs? I may go ahead and prototype one board, but I'm not very confident that this is going to be a viable project, for both this reason and the reason Ben gave: the wimpy LEDs will be competing not only with ambient light, but with other lights in the display (minis, C7's) that give off much more light.
Which LEDs are you using? What size, what vendor?
I think that there is quite a bit of variability from one RGB LED to the next. I'm playing around with some RGB LEDs also. The ones that I have are all 5 mm so far. Some that I've seen are the way that you describe, while others mix a lot better. Some expensive (but discontinued) RGB LEDs that I purchased from mouser had frosted lenses, and were pretty good at mixing. Others from various EBay sources did have some tendency to show individual pools of light. I think that you might want to look at other sources as well, you may find some that you like.
--
Phil
DJ, I was thinking I might have to do that. I'm not sure that having to manually bend a ton of LEDs to point in the same direction is going to be a very DIY-friendly proposal. 🙂
Phil, my LEDs were 5mm clear lens common anode from JELEDHK on ebay. I also wonder if frosted lens LEDs would work better. I'll have to lay hands on some frosted LEDs and see what the results are.
In any case, this project is sounding like it might not be worth the effort.
Using a belt sander on the rounded parts of the LED's to make them more flat also makes them diffuse the lights a little better. Bending them to the right position is as easy as taking a ruler to the LED lineup (best configuration) and pushing them a bit to the desired direction.
