8 channel SSR
 
Notifications
Clear all

8 channel SSR

11 Posts
6 Users
0 Reactions
4,376 Views
john2571
Posts: 66
Topic starter
(@john2571)
Trusted Member
Joined: 14 years ago
[#20610]

This is my first attempt at creating a PCB design myself and have made a compact 8 channel ssr. I have not put the mounting holes in this yet but I nelieve fot the nost part it is done. This is based off of the dirkcheap ssr and is for low current application. Please tell me what thing should be changed.
-John

Parts bellow-

2- http://www.digikey.com/scripts/DKSearch/dksus.dll?Detail&itemSeq=118747877&uq=634813541878742502
8- http://www.digikey.com/scripts/DKSearch/dksus.dll?Detail&itemSeq=118747916&uq=634813541878742502
8- http://www.digikey.com/scripts/DKSearch/dksus.dll?Detail&itemSeq=118747935&uq=634813541878742502


10 Replies
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

You generally don't want to run traces beneath the chips, and especially when the traces are so close to the hot (120vac) lines. If you looked closely at the DirkCheap board, you'd have noticed that the 120VAC power traces are also duplicated on both the top and bottom of the board, which not only increases its capacity but makes it safer as well. Otherwise, some good potential there! ExpressPCB is fun to use!

EDIT: Some of the traces have 90-degree corners, which can trap the etching liquid (generally an acid) and it may not etch consistenty.


Reply
john2571
Posts: 66
Topic starter
(@john2571)
Trusted Member
Joined: 14 years ago

Re-ran all of the traces, eliminated most 90 degree corners, and doubled up the 102vac traces. Think it is ready to be ordered?
-John


Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

A few notes:

There are a number of places where traces run too close to pads. As a rule of thumb, I try to keep traces at least 10 mils away from other traces and pads.

You don't have any mounting holes

I'd add a note in the silkscreen with the name, date, and revision of the board

/mike


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Better! Check your channel numbering... I think channels 4-3-2-1 are actually 1-2-3-4 and 5-6-7-8 are actually 8-7-6-5. Traces are awfully tight around the RR45 pins too... you might consider running the bottom traces between the resistors and that would give you a lot cleaner, straighter trace and eliminate some of those tight corners. The main reason for not running them under the VO chips is the proximity to 120vac, but secondarily, it's cleaner electrically, too and can lessen electrical interference. It's okay to run them under resistors because a resistor doesn't have a lot of internal circuitry like a chip does. Also, you'd want to center that common power connection at the end of the board -- it's pretty close to the VO chip.

Before you send it off, print it out on paper. Test parts for the fit. Make sure the holes for your A/C power cables are big enough but not way too big -- if they're too big for the cables, you'll have to glob on the solder something fierce to fill the hole.

How much juice are you going to put through this? Having 8 channels can max out at 8 amps if you load each with 1 amp. Even doubled-up, those power traces are only .05 wide, and that's not very wide for potentially that much current. If you're planning to use these with LED strings you'll be fine, and even 8 mini-incans would probably be okay (3A total). You might check the load-carrying capacity of what is essentially 2 oz copper at .05" wide (2oz because it's doubled-up on top/bottom of board). The normal boards from Express PCB are 1oz copper.

You're doing a good job, John. Keep at it!

EDIT: Mike raises some good points! His comments have helped me a lot in the past...


Reply
john2571
Posts: 66
Topic starter
(@john2571)
Trusted Member
Joined: 14 years ago

I have finished everything. I might not be adding mounting holes as these will be mounted in 2 inch pvc pipe. If there is anything I should fix please tell me.
-John
Pictures bellow-
http://gyazo.com/518ed54d06a2c7386479567c9ad88c91
http://gyazo.com/90995d5783e230101f9d7b155a4319a1
http://gyazo.com/eaffd5f6dd5d514d304416c1b1639776

Edit- Fixed the numbers and have uploaded a revised version.


Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

Looks good. I did a little cleanup; here's the updated board.
/mike


Reply
N7XG
Posts: 480
 N7XG
Guest
(@n7xg)
Member
Joined: 19 years ago

It looks like you might be missing he fuse.


Reply
john2571
Posts: 66
Topic starter
(@john2571)
Trusted Member
Joined: 14 years ago

Planing on using the plug from a Christmas lights strand with the fuse in it as these are for low current only and I will be using only LEDs.
-John


Reply
Posts: 6
(@djflexdex)
Active Member
Joined: 15 years ago

What program did you use to create the file?


Reply
Page 1 / 2
Share: