8-channel Renard Se...
 
Notifications
Clear all

8-channel Renard Servo Controller

47 Posts
12 Users
0 Reactions
23 K Views
omzig
Posts: 1603
Topic starter
(@omzig)
Noble Member
Joined: 19 years ago

Unfortunately I am going to have to scrap my plans for this project this year. I simply don't have the time to work on it. I now have another remodeling project that has to be completed quickly because it looks like my wife's uncle is going to be moving in with us for a while because of medical issues. I am going to expand the in-law suite that I built for my father-in-law last year to accomodate him. It's going to be hard to find time for any BF things.

If anyone would like to see the firmware that I wrote for this, let me know.


Reply
Posts: 2168
(@djulien)
Noble Member
Joined: 19 years ago
omzig wrote:If anyone would like to see the firmware that I wrote for this, let me know.

Yes, I would like to take a peek.

don


Reply
Posts: 999
(@ppohlman)
Noble Member
Joined: 19 years ago

I'm sorry to hear that this project is being postponed. I was really interested in the final product.

More importantly I hope that your wife's uncle is/will be doing better.

Are you planning on posting the firmware here or are you going to send it to people? I'd like to play with it when I get time too.

Thanks for all that you've done with this so far.


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

I was also watching this project. I’ve never played with servos before but they looked to be interesting. I know that a lot of people just buy the servos but it looks like they’re not too hard to build. Supposedly it’s not too hard to turn most motors into a servo. It seamed like a good use for wiper motors.

Think of a Christmas present or Jack-In-The-Box where the top opens and closes and you only need the motor. No switches to detect where to stop.

How about a Santa’s workshop present making machine where the parts actually move.

If you’re sending the code out, I’d like to be on that list. Not that I need something else to do, I don’t want to see this get lost either.


Reply
omzig
Posts: 1603
Topic starter
(@omzig)
Noble Member
Joined: 19 years ago

I'll post the firmware here. I need to figure out which version though. There were many different versions because I couldn't decide how to handle the changing of settings. I never did really make up my mind, but I was leaning toward using one of the 8 channels as a control channel.

I need to clean the code up a little and add a few more comments and then I'll post it.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

This topic seems to be on hold, but I had a thought...

With the newer Renard plugins I think that it is not necessary for a controller to use exactly eight channels worth of data in the stream. What the controller would need to do is simply remove the amount of data that it needs from the data stream, nothing more. It might be possible to do a similar trick with the data stream generated by the earlier Renard plugins (for Vixen 1.x), but it might be difficult to write the code that would work there (the controller would need to hold more state information than previously, essentially packet re-assembly). But the benefit of this is that a servo controller, for example, could use one channel for control/configuration information and the other channels for the servo position information.

Also, it would be a little more complicated explaining things to people writing sequences, since some of the old ways of thinking would be changed.


Reply
g2ktcf
Posts: 3651
(@g2ktcf)
Famed Member
Joined: 18 years ago
P. Short wrote:This topic seems to be on hold, but I had a thought...

With the newer Renard plugins I think that it is not necessary for a controller to use exactly eight channels worth of data in the stream. What the controller would need to do is simply remove the amount of data that it needs from the data stream, nothing more. It might be possible to do a similar trick with the data stream generated by the earlier Renard plugins (for Vixen 1.x), but it might be difficult to write the code that would work there (the controller would need to hold more state information than previously, essentially packet re-assembly). But the benefit of this is that a servo controller, for example, could use one channel for control/configuration information and the other channels for the servo position information.

Also, it would be a little more complicated explaining things to people writing sequences, since some of the old ways of thinking would be changed.

Phil,

Don and I discussed this a way back. We both felt that it would be too confusing to the user to have to remember any special things while sequencing. The reason we were discussing it was being able to "intialize" the controller with some servo parameters.

Chris


Reply
Page 5 / 5
Share: