Forming plastic she...
 
Notifications
Clear all

Forming plastic sheet

13 Posts
7 Users
0 Reactions
8,069 Views
Posts: 50
Topic starter
(@docjon)
Trusted Member
Joined: 19 years ago
[#25142]

Hey guys, Hope you are all well and aren't crazy yet planning this years display 😛
I have a quick question that I hope you can help me with.
I am working on a project (non Xmas related...although all the elements I create for this project I can use for Xmas later) in which I need to take a 5cm wide strip of white plastic which is 5mm thick, and mold it into a half tube. I have done a quick test using a heat gun and a broom handle and I am happy with the overall result. Pics are attached.
I was wondering if there is an easy way to heat it up and form the curve as I need to create lengths of this half tube up to 1m long.
I know in the pictures that the edges are a bit rough, and hopefully I will be able to find a way to make smooth edges.

Any tips or previous experience would be greatly appreciated.
Thanks

Bent plastic 1
Bent plastic 2

12 Replies
beeiilll
Posts: 869
(@beeiilll)
Prominent Member
Joined: 19 years ago

To get the edges smooth I would think that you would need to use a central cylinder and an outer wrap to go over the sheet and form it. Much like a mandrel and outer press or else use a form of vacuum forming around a central cylinder although you can't be assured about the edges with that method.

Probably use a hot water bath to heat the sheet and then form around the broom handle by rolling the sheet around it and having something to hold the sheet tight while it cools (at least on the edges so that they stay flat and straight). Maybe a long piece or two of angle aluminum to hold the edges tight to the cylinder.


Reply
Posts: 353
(@bigredsoftware)
Reputable Member
Joined: 15 years ago

This is known as drape forming. You should heat the pieces in your oven. Check for annealing and forming temps of your plastic type. You also want some pressure on the other side with some short of negative mold. You could also cut the pieces longer and clamp around the handel, saw drops later. The key is to hold the shape while cooling. What kind of plastic? We do this type of stuff at my work, so I can get you some proper temps.


Reply
Posts: 50
Topic starter
(@docjon)
Trusted Member
Joined: 19 years ago

Thanks for the replies. All the info I have about the plastic is that it is a 5mm PETG plastic, I don't know if that is helpful at all.
I will be able to get more information when I pick up the bulk amount hopefully later this week or next week.


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Not sure about the 1m length, but VACUUFORMING would get you a cleaner edge. Oddly enough I'm about to try building a vacuuform sometime in the next week. (Albeit smaller than 1m in size).


Reply
somtng4u2c
Posts: 557
(@somtng4u2c)
Prominent Member
Joined: 18 years ago

could you use pc pipe cut in half


Reply
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 20 years ago

what about a die/mold? Use your broom stick and cut a piece of pipe in half, heat the plastic sheet while laying on the mold (pipe) then press the die (broom stick) in the mold.


Reply
Posts: 353
(@bigredsoftware)
Reputable Member
Joined: 15 years ago

Well I talked to the forming guys today and the temperature for PETG should be anywhere from 150 degrees to 170 degrees. But here's the problem, the plastic you are holding in your pictures does not look to be five millimeters thick or PETG. PETG is typically clear from what I have seen, but what you are holding looks like PTFE or otherwise known as Teflon. This is one of the most expensive Plastics you can buy, but it would hold up to the weather very nice. 5 millimeter is almost quarter inch thick, and sheets are typically sold in 6 millimeter thickness to match the Imperial quarter inch as close as they can. Check your thickness with a caliper. I like Wayne's suggestion of using another piece such as a half of a tube to guarantee your shape on the other side. One of the things the forming guy mentioned to me was that PETG is very easy to work with but can be overheated very quickly giving you an imperfect surface that will contain many ripples. You will have to experiment on the proper heating times. Also get yourself a good pair of cotton gloves that are decently thick so you can safely handle the plastic without hurting yourself or leaving imprints on the surface.


Reply
derekbackus
Posts: 565
(@derekbackus)
Honorable Member
Joined: 15 years ago

We do this sort of thing all the time at work. The limit is the size of your oven. The martini glass on our site was formed that way http://www.kiwimill.com/night-club-display-model/

This looks like PVC or ABS to me, but could be anything, really.

What I'd try... cut the broom handle to the size of your oven, put the plastic on top (might be hard to balance it... maybe a thumb-tack on both sides) and it should drape over the handle. I've never done this exact method. We quite often cut a hole in wood and drape the plastic for a dome -- same idea. The trick is UNIFORM heat (an oven). It is very difficult to do this with a heat gun (as you found out).

And, like everyone said -- you'll have to experiment with temperature -- don't rush it or you'll end up with bubbles on the plastic from too much heat. Oh, and DO NOT burn PVC. Bad...


Reply
Posts: 50
Topic starter
(@docjon)
Trusted Member
Joined: 19 years ago

Hey guys, thanks for all of your responses.
I should have clarified a few things earlier, the sample in the pics is just some styrene plastic sheet I have had left over from model building, its 0.75mm thick. The plastic that I am looking to purchase for this project is PETG 0.5mm thick, the supplier has said that it comes in white, I am just double checking this with them now, maybe they put down the wrong name as i did ask them for quotes on a few different things.


Reply
Page 1 / 2
Share: