I did some work on the 12v version. Here is what I have so far. I need some feedback. On this idea... As a side note I added some 12v 5050 strip LEDs to my last order so I can test this.
First some questions and assumptions.
1). How much current are you wanting to power? The 5v version I designed to handle 1 50ct string. (3a)
2) does the 2.1mm dc jack need to be there? I put it on the 5v for simplicity. Not sure what power supplies are being used for the 12v but I suspect they vary. Would it be better to add a header for an optional terminal block instead of the dc jack? This way the wires could be soldered to the board or you could choose to add a terminal?
3) for the firmware, what pixels? Would supporting fastspi2 cover it?
Ok, now the options.
12v input with one pad nearby for full current output 12v/3a?
Before the voltage reg
I am thinking of adding a Zener diode to drop the 12v down to 10v
At 10v I could put a
http://www.onsemi.com/pub_link/Collateral/MC78M00-D.PDF
This would allow the 328 to run at 5v
For the 3.3v power to the transceiver ill add another Zener to drop the voltage to 3.3 the radio pins are 5v tolerant so only the power needs to drop.
We could also use a similar voltage regulator to the current board (mcp1700) but it needs the input voltage dropped to 6v. I wasn't sure that dropping 6v with a diode was a good idea?
Thoughts? I have some of the mc7800 regulators so Ill wire one and see
If I stay with the mcp1700 series the diodes could be skipped and just bypassed with a jumper or 0R and the board could work at 5/3.3 also
Also a possibility to use the same 5v regulator and let the chip run at 4.8v when powered by a 5v supply.
The board will have to be a bit longer for any of this which is a bummer because the pcbs cost more to make 2 on a 5mmx10mm instead of a 5mmx5mm. I won't need the. Full 10mm either unless that's ok ?
komby wrote:1). How much current are you wanting to power? The 5v version I designed to handle 1 50ct string. (3a)
Like the old TV character Tim "The Tool Man" Taylor used to say, "More power!"
If the DIY LED Express "PixaBulbs" are any indication (Todd says they're "~50ma on full white,"), you could do 50 with a 3-amp circuit and would probably need a 6-amp circuit to do 100.
komby wrote:2) does the 2.1mm dc jack need to be there? I put it on the 5v for simplicity. Not sure what power supplies are being used for the 12v but I suspect they vary. Would it be better to add a header for an optional terminal block instead of the dc jack? This way the wires could be soldered to the board or you could choose to add a terminal?
Just give me a Phoenix terminal block space ... the barrel jacks are nice for simplicity, but heavens knows what would drive the higher amperage circuit (most likely not a wall wart).
komby wrote:
3) for the firmware, what pixels? Would supporting fastspi2 cover it?
See above note on PixaBulbs -- that'd be a WS2811 @ 12v.
komby wrote:
Thoughts? I have some of the mc7800 regulators so Ill wire one and see
I guess I'm being dense ... I can't see the difference between the mc7800 and a garden-variety lm7800, except the price, which seems to be almost a buck each ...
komby wrote:
If I stay with the mcp1700 series the diodes could be skipped and just bypassed with a jumper or 0R and the board could work at 5/3.3 alsoAlso a possibility to use the same 5v regulator and let the chip run at 4.8v when powered by a 5v supply.
Usually the way folks have designed 5v/12v items is to expect the builder to omit a LM7805 (or similar) from the circuit while soldering, instead jumpering pins 1 and 3 in that socket in order to provide the circuit with its own 5v from the power supply.
komby wrote:
The board will have to be a bit longer for any of this which is a bummer because the pcbs cost more to make 2 on a 5mmx10mm instead of a 5mmx5mm. I won't need the. Full 10mm either unless that's ok ?
Design it as a 5mm x 7.5mm board and place two on a 5mm x 15mm master board, with a silkscreen for score and snap.
HTH.
\dmc
komby wrote:
1). How much current are you wanting to power?
A typical 5v pixel runs about 60ma each, or 3 A for 50. The most one would want to run without power injection is 60ish, or about 3.6A.
A typical 12v pixel runs about 30ma each, or 3A for 100, 3.7A for 128 (longest string Ray Wu sells, also RJ's maximum)
Ray's 45W waterproof 12V ps is 3.7A (45W).
The pixabulb is apparently higher current, but 3.7A should still handle about 70 @ 50ma.
The connectors I'm considering are rated for 3 or less than 4A.
I think 3.7A or so would cover the most common use cases, but 3A would be fairly good. If you really want more than that, it's not unreasonable to use an external wiring harness and not go through the traces.
komby wrote:
2) does the 2.1mm dc jack need to be there?
The 2.1mm barrel jack is common for 5 and 12v supplies. But I was thinking to probably omit the jack and just solder to the pads, so I could use my own choice of connector. I am thinking to use different connectors for 5V and 12V but I'm still sorting that out.
komby wrote:
3) for the firmware, what pixels? Would supporting fastspi2 cover it?
Yes, I think that covers it. I would be creating my own firmware as I want a different over the air protocol, but probably use the FastSPI_LED2 library, as it supports all the pixel types I have (*), and the version 2 is fast and compact. So being able to use the Uno bootloader is important. Which version bootloader were you planning to use?
(* I have some 1829 samples, and clued Dan G into those, and he was clearly intrigued, so FastSPI_LED2 is likely to try to support them too if possible. The 1829 is a 3 wire type like the 2811/1804 but twice as fast to update, and may have a much faster PWM cycle.)
It sounds like you are considering running at 5V. Is that mostly to be within ATMega328P spec's at 16 MHz, or to give a 5V swing to the outputs for driving pixels?
komby wrote:
For the 3.3v power to the transceiver ill add another Zener to drop the voltage to 3.3 the radio pins are 5v tolerant so only the power needs to drop.
Has that been tested? (Using a Zener to power the transceiver from 5v). My concern would be that it's not really regulated, so I hope the power would be steady enough not to interfere with the transceiver operation.
komby wrote:
We could also use a similar voltage regulator to the current board (mcp1700) but it needs the input voltage dropped to 6v. I wasn't sure that dropping 6v with a diode was a good idea?
Real world diodes have a current to voltage curve rather than a cliff, so if the load varies there would be some voltage variation too; I'd be cautious about dropping that much in the diode.
komby wrote:
The board will have to be a bit longer for any of this which is a bummer because the pcbs cost more to make 2 on a 5mmx10mm instead of a 5mmx5mm. I won't need the. Full 10mm either unless that's ok ?
Is there any chance of putting components on both sides?
dmcole wrote:I guess I'm being dense ... I can't see the difference between the mc7800 and a garden-variety lm7800, except the price, which seems to be almost a buck each ...
Usually the way folks have designed 5v/12v items is to expect the builder to omit a LM7805 (or similar) from the circuit while soldering, instead jumpering pins 1 and 3 in that socket in order to provide the circuit with its own 5v from the power supply.
Design it as a 5mm x 7.5mm board and place two on a 5mm x 15mm master board, with a silkscreen for score and snap.
HTH.
\dmc
Come to think of it, won't both those if connected to 12 v get too hot without a heat sink? I think zeph might have to use black pipe instead of PVC for an enclosure .
Should I be worried? I'd be happy to use them cause I have a bunch of the 7805s sitting here but I figured they get too hot?
I like the 5mmx15mm idea that is 4 per at 2.5mmx7.5mm Ill shoot for that
komby wrote:Come to think of it, won't both those if connected to 12 v get too hot without a heat sink? I think zeph might have to use black pipe instead of PVC for an enclosure.
I guess I'm still too dense ... why would you run the power for the pixels through the voltage regulator (assuming this as for why the x7805 would get hot)?
I thought the MCU controlled the signal only and you'd send power down the line without passing it through the MCU?
Or am I way off base here?
If all the voltage regulator is powering is the MCU and assorted other on-board bits, why would it get hot? (If it is powering pixels, I could see why it would get hot).
\dmc
PS: I realized while pondering these questions that we've never seen schematics of this project.
