jetty
@jetty
Estimable Member
Joined: Dec 5, 2012
Topics: 9 / Replies: 143
Reply
RE: Mega 2560 and renard protocol

codec101 wrote:My mega is running with the Renard protocol and is setup for 32 channels. I was running up to 16 at once this past Halloween for two ...

12 years ago
Forum
Reply
RE: Mega 2560 and renard protocol

cpwtech wrote:Has any one been able to get a Mega 2560 to use the Renard Protocol? I have a Mega here and 3 Uno's. The Uno's are using the protocol,...

12 years ago
Forum
Reply
RE: E1.31 Arduino GECE controller

jchuchla wrote: I've never seen #defines use parens. I'm not sure if its allowed, but I don't think it is. It's normal to use parens in defines. F...

12 years ago
Forum
Reply
RE: FoxCub V2 Wish List

It's certainly something that can be looked into. I think the ideal solution would be that or BLE, as the ESP becomes better supported, it would be a...

12 years ago
Forum
Reply
RE: FoxCub V2 Wish List

Personally I like to keep things simple, that means using stuff that's reliable and making it as simple as possible. I.E. I'm not of the mindset to s...

12 years ago
Forum
Reply
RE: help with code please

LightUp wrote:Where is the other "or" method? 🙂 Oops, meant to delete that. There will be an "or" method when I get a few cycles.

12 years ago
Forum
Reply
RE: help with code please

jchuchla wrote:I believe Jetty's foxcub project is exactly that. He reads Renard and controls AC lights in an arduino sketch. That's correct, 16 chan...

12 years ago
Forum
Reply
RE: Optimizing code for simplicity and newbies, for using Arduino with relay boards.

LightUp wrote:I heard that there were "fake" Arduinos and I didn't know which supplier used the "fake" versions. Adafruit supposedly doesn't, hence my...

12 years ago
Forum
Reply
RE: Optimizing code for simplicity and newbies, for using Arduino with relay boards.

Shockwave wrote:If I could do it 9 years ago, you can do it now. Yes, if you drop to 32 levels of brightness instead of 256, you could use all channe...

12 years ago
Forum
Reply
RE: Cold Weather Failures

It would depend on the driver chip and the led used, if both aren't rated for operation at that temperature, you will likely start to see issues. In y...

12 years ago
Reply
RE: Optimizing code for simplicity and newbies, for using Arduino with relay boards.

LightUp wrote:They just look for faster ones. For this reason I have no qualms about bit-banging as a solution, in spite of its challenges. For all I ...

12 years ago
Forum
Reply
RE: FoxCub PCB's

2 boards gone. 1 x FoxCub16 PCB left.

12 years ago
Reply
RE: Optimizing code for simplicity and newbies, for using Arduino with relay boards.

LightUp wrote:He used Generic Serial, and used 32 channels of dimming. Since his configuration is working I don't see a problem. It depends on the d...

12 years ago
Forum
Reply
RE: Optimizing code for simplicity and newbies, for using Arduino with relay boards.

Matt_Edwards wrote:I may have mentioned this elsewhere, but RPM's grinch dimmer does 64 channels at full 256 levels ac dimming. It uses the spi bus t...

12 years ago
Forum
Reply
RE: Optimizing code for simplicity and newbies, for using Arduino with relay boards.

jetty wrote:you need to go to SPI and shift registers, and even then, that's only gets you to about 32 channels before you'll get stability issues. ...

12 years ago
Forum
Page 2 / 11