Keeping an effect l...
 
Notifications
Clear all

Keeping an effect loop between shows

11 Posts
7 Users
0 Reactions
3,693 Views
relic1882
Posts: 104
Topic starter
(@relic1882)
Estimable Member
Joined: 12 years ago
[#43885]

It's there a way to loop an animated sequence (without music) in between shows? I tried to make a sequence that twinkles a few colors and add it to a schedule but when it finishes and comes back around it has a split second where it goes black.

Sent from my SM-G920V using Tapatalk


10 Replies
Ronnie
Posts: 206
(@ronnie)
Reputable Member
Joined: 11 years ago
relic1882 wrote:It's there a way to loop an animated sequence (without music) in between shows? I tried to make a sequence that twinkles a few colors and add it to a schedule but when it finishes and comes back around it has a split second where it goes black.

Sent from my SM-G920V using Tapatalk

I had this problem in xlights until someone pointed out to make sure the effects go past the end time in the sequencer. I stretched them out to just past the end time and that fixed the problem. Not sure if it's the same with Vixen, but might be worth a look.


Reply
relic1882
Posts: 104
Topic starter
(@relic1882)
Estimable Member
Joined: 12 years ago

I don't see a way to go play the end time in Vixen. Perhaps I'll just run x lights manually when I'm not doing my show.

Sent from my SM-G920V using Tapatalk


Reply
Ronnie
Posts: 206
(@ronnie)
Reputable Member
Joined: 11 years ago
relic1882 wrote:I don't see a way to go play the end time in Vixen. Perhaps I'll just run x lights manually when I'm not doing my show.

Sent from my SM-G920V using Tapatalk

Here's an excerpt from Vixen's documentation... "Looping is also possible. By selecting the loop button on the play bar the sequencer will play in a loop the entire sequence or the selected play range.

Have you tried selecting a section that is just short of your end time? See if that eliminates the quick black period.


Reply
relic1882
Posts: 104
Topic starter
(@relic1882)
Estimable Member
Joined: 12 years ago

My shoes is running right now but I will try it tomorrow.

Sent from my SM-G920V using Tapatalk


Reply
jeffu231
Posts: 2457
(@jeffu231)
Famed Member
Joined: 15 years ago

Looping in the editor will be continuous. The editor is able to reset the play pointer in a single sequence it is running. It is only in the scheduler that the blink will occur because of some limitations in the way the scheduler works. There is no work around to eliminate the blink in the scheduler, unless your sequence is truly the same all the way through. If it is just static lights with no transitions, you can make a shorter version of the same static sequence and add it as a background sequence to run at the same time. The two will merge and it will no longer blink because the end of each one will overlap. Again the sequence has to be static for this trick to work.


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago
relic1882 wrote:My shoes is running right now

Sure sounds easier than going to the gym!


Reply
Posts: 259
(@cmschleich)
Reputable Member
Joined: 11 years ago
deonb wrote:Sure sounds easier than going to the gym!

Falcon Player can do that, if you're using it as the show player.

Sent from my iPhone using Tapatalk


Reply
relic1882
Posts: 104
Topic starter
(@relic1882)
Estimable Member
Joined: 12 years ago

Haha. Just got my first smart phone about a week ago and the autocorrect on it gets retarded sometimes.

Sent from my SM-G920V using Tapatalk


Reply
Posts: 2
(@bigfish24)
New Member
Joined: 10 years ago

The blink is a huge annoyance when using the scheduler. My shows are basically just house outlines and wreaths that display a different theme every night. Going for the "keeping it classy" look. Since the show doesn't change all night...I would like to have it continue to repeat until the end of the night schedule. The brief ON/OFF period makes that very distracting. I have compensated by making the shows VERY LONG (like 15 minutes) so the blink will only appear periodically. I've tried running the sequence as a background and that does not solve the problem either. Got to be a fix for this??


Reply
Page 1 / 2
Share: