Hi All,
My current setup is as follows:
Vixen v3 (lates build) and I have one "streaming ACN (e1.31)' controller configured w/ 7477 outputs.
1 Falcon 16 v2
5 Renard 24s Boards
1 RenLSD48
They are in a daisy chain configuration with the Falcon v2 leading the way. I just purchased a second Falcon 16v3 and I am not certain of two things:
1 - In Vixen do I add it as a second "streaming ACN (e1.31)" controller or simply add the universes, ie I now have 14,477 outputs b/c I added 4k (as an example).
2- Physically, I believe that IF i setup the Falcon, in Vixen, as additional universes (part of the same 1 controller) it MUST reside in the end of the daisy chain.
Thank you for the help
Your daisy chain is a Chain of Renard devices using the Renard Serial protocol that Starts at a Falcon serial port and ends at the last Renard device. Just because the chain uses a CAT5 cable, does not mean you can plug any old device into the chain.
The Falcon controllers use E1.31 (Streaming ACN) transported via Ethernet delivered to the falcon via a CAT5 cable on an Ethernet interface. Adding a 2nd Falcon controller means you will add the 2nd device to the Ethernet Show Network. Yes you will need to add a 2nd Streaming ACN (E1.31) controller to vixen and assign the data you want that controller to use.
MartinMueller2003 wrote:Your daisy chain is a Chain of Renard devices using the Renard Serial protocol that Starts at a Falcon serial port and ends at the last Renard device. Just because the chain uses a CAT5 cable, does not mean you can plug any old device into the chain.Thanks Martin -
The Falcon controllers use E1.31 (Streaming ACN) transported via Ethernet delivered to the falcon via a CAT5 cable on an Ethernet interface. Adding a 2nd Falcon controller means you will add the 2nd device to the Ethernet Show Network. Yes you will need to add a 2nd Streaming ACN (E1.31) controller to vixen and assign the data you want that controller to use.
So, in Vixen I add a second controller - and assign data / elements to that device. - understood.
Architecturally, I cannot daisy chain it, b/c after the falcon v2 the protocol is Renard - got that. So, then the New flacon needs a NEW rj45 to send it data to it. It cannot be on the same chain as the old falcon and renards. Is that correct?
Correct. Strictly speaking, you cannot daisy chain ethernet connections. Each ethernet device needs to be connected to its own port on a switch.
That being said, there are products out there that make this more confusing. The F16V3 for example, has a built in 3 port ethernet switch. There's two ethernet ports available to you, and a 3rd connected internally to the device itself. So you can connect one of those ports to the main ethernet switch, and the other to another controller, or any other ethernet device. This makes it look like you're daisy chaining it, but in reality, it's really just the same thing as if you put a cheap 4 port switch in the box right next to your controller.
jchuchla wrote:Correct. Strictly speaking, you cannot daisy chain ethernet connections. Each ethernet device needs to be connected to its own port on a switch.That being said, there are products out there that make this more confusing. The F16V3 for example, has a built in 3 port ethernet switch. There's two ethernet ports available to you, and a 3rd connected internally to the device itself. So you can connect one of those ports to the main ethernet switch, and the other to another controller, or any other ethernet device. This makes it look like you're daisy chaining it, but in reality, it's really just the same thing as if you put a cheap 4 port switch in the box right next to your controller.
Jon,
Tracking....
Now, IF (big IF) i were to use the Falcon v3 version, I believe you are referring to the DMX1 jack (nearest to the top of the board) as the "ethernet port" to act as a "switch"? If that is correct, still assuming I go down this route. I would "mimic" Falcon v2 settings for the new Falcon v3 and daisy chain the existing Ren boards (essentially replacing the V2). However, I would then attach the Falcon v2 to the "switch" port.
Is that correct?
