Hi guys
I have an (weird) issue with a sequence where I get a sort of missfire on the pulse effect. You can see it this video:
I have a series of pulses that activate with the timing of the beat in a song. The pulse have this intensity curve:

And the pulses are 0.781 seconds long.
I think it only happens in this sequence, because I first tried to switch out my hardware but that didn't do anything. Then I tried adjusting timings on my hardware but that did not do anything either. Then I copied the offending pulses to a new sequence and there it worked fine. I also tried running different sequences and they did not have any pulse issues.
But what strikes me as really odd is that the missfire is random. Every time I play the sequence, the missfire happens in different places. Color choice has no effect, and pulses with other intensity curves are fine in the same sequence.
What can cause this?
PS. Running version 3.3.
If your pulse is 0.781s in duration, and you have 20 steps in the curve, each linear intent in your pulse is only 39ms long which is shorter than a single update of the engine. Each pair or points in your curve cause the effect to generate what we call a linear intent. A linear intent is a value that changes in a linear fashion from one value at one point in time to another at a second point in time. The engine samples this line for the current point of time and uses that value. (Linear interpolation) It's actually counterproductive to put more changes in the system than it could ever possibly use.
Try to remove at least half of those nodes in your curve. From a practical point of view, you probably only need 3 intermediate points to achieve the same result visually.
--Jon Chuchla--
Sent from my iPhone using Tapatalk
Okay, I can try. I does however work in another sequences flawlessly, via a simple copy paste.
When you're pushing the limits, weird things can happen. Perhaps the other sequence where it's working has less intents in the engine at the point of time when its trying to process them than this sequence does.
--Jon Chuchla--
Sent from my iPhone using Tapatalk
jchuchla wrote:When you're pushing the limits, weird things can happen. Perhaps the other sequence where it's working has less intents in the engine at the point of time when its trying to process them than this sequence does.--Jon Chuchla--
Sent from my iPhone using Tapatalk
Ahh, that actually makes sense and a good thing to know about the system when sequencing. And simplifying the curve helped, no more 'artifacts'. My new curve is this now:
I may tweak it a little more, since the first two points are quite close to each other.
This level of detail about how it works is more than most people need to know. But sometimes it helps to explain it when I see someone who is overthinking their sequencing.
There's actually even more going on under the hood than I explained. But the point remains, don't give the software more work to do than it could possibly make use of.
Your original curve would probably work just fine on a longer effect. Perhaps even a slightly longer effect (over 1 second). And if it were a much longer effect, all those points would probably pay off and make it look really good.
On another note. I'm not sure how you're using this pulse in comparison to other pulses in your show. But this curve looks like a curve you'd use to adjust led lights to match the visual linearity of incandescent lights. If you are doing this curve in the pulse, you probably are use interface the same curve for every single pulse. This is a use case where you'd be better served by setting up dimming curves in the patching rather than doing it in every effect. If you do that, your pulses would be straight diagonal lines and no need to deal with the complex curves in the effects. It makes sequencing easier. And it also puts a lot less burden on the engine.
--Jon Chuchla--
Sent from my iPhone using Tapatalk
jchuchla wrote:On another note. I'm not sure how you're using this pulse in comparison to other pulses in your show. But this curve looks like a curve you'd use to adjust led lights to match the visual linearity of incandescent lights. If you are doing this curve in the pulse, you probably are use interface the same curve for every single pulse. This is a use case where you'd be better served by setting up dimming curves in the patching rather than doing it in every effect. If you do that, your pulses would be straight diagonal lines and no need to deal with the complex curves in the effects. It makes sequencing easier. And it also puts a lot less burden on the engine.
Good tip, but this sequence audio has some rather tight finger snaps. Rather than having the pulse dimming normally i wanted a fast dimming process, but also let it linger in the reverb/ekko portion of that particular sound.

