Major Vixen Problem...
 
Notifications
Clear all

Major Vixen Problems.

19 Posts
9 Users
0 Reactions
7,408 Views
Posts: 34
Topic starter
(@dv3894)
Trusted Member
Joined: 17 years ago
[#10285]

I have three parallel pots, one a printer, and two PCI cards. My controller will not work with vixen.

Some information:

  • Vixen's "Simple 595" plugin will work only one relay when hooked to the printer port, but none with the other ports.
  • Some other parallel plugins will not do anything and/or will give me the message: "Source array was not long enough. Check SrcIndex and length, and the array's lower bounds."
  • (No idea what that means)
  • Sometimes when I start the application and an error message says "The program is about to die..." What does that mean?
  • I have the latest version of Vixen
  • I have verified the correct driver for the ports
  • Device manager states there are 2 PCI Parallel ports
  • Have a "qkit's 8 channel parallel relay I/O device
  • When my controller is pluged in and the computer is started, all relays are on
  • Program that tests relays only works when controller is plugged into printer port
  • I have seen people have the same configuration of vixen and this relay device.

18 Replies
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago

I think you might want the Basic Parallel plug-in instead of the Simple 595 (unless your device has a shift register for decoding the incoming data).


Reply
Posts: 34
Topic starter
(@dv3894)
Trusted Member
Joined: 17 years ago

It looks like the board only uses a 2803A relay driver IC.
I will try that plugin.


Reply
Posts: 34
Topic starter
(@dv3894)
Trusted Member
Joined: 17 years ago

Thank you so much, that worked, but it only works with the printer port. The PCI cards are not being recognized by Vixen. And since my controller has two boards, we are only defeating half the battle. -- Thank you so much for your help, I am open to any suggestions.


Reply
Aurbo99
Posts: 2804
Moderator
(@aurbo99)
Member
Joined: 19 years ago
dv3894 wrote:I have three parallel pots, one a printer, and two PCI cards. My controller will not work with vixen.

Some information:

  • Vixen's "Simple 595" plugin will work only one relay when hooked to the printer port, but none with the other ports.
  • Some other parallel plugins will not do anything and/or will give me the message: "Source array was not long enough. Check SrcIndex and length, and the array's lower bounds."
  • (No idea what that means)

It almost sounds like you did not define which port to use in the setup.

As well the Source array error is usually an indication you did not identify the upper and lower channels for each plugin instance.

Sometimes when I start the application and an error message says "The program is about to die..." What does that mean?

Just that, it does not like its current setup and whatever configuration you have is causing Vixen to shut down.

I have the latest version of Vixen

If you have 2.5 or greater, you may have to drop back to 2.1, there has been soem issue with the recent 2.5+ version.

I have verified the correct driver for the ports

  • Device manager states there are 2 PCI Parallel ports

ECP?, EPP? port settings? what are the port addresses?

Have a "qkit's 8 channel parallel relay I/O device

  • When my controller is pluged in and the computer is started, all relays are on
  • Program that tests relays only works when controller is plugged into printer port

Does the test program turn off and on the controllers?

  • I have seen people have the same configuration of vixen and this relay device.

Did you see it? and copy their setup? or just hear or read they have a similar setup? Important for troubleshooting.. If you actually saw it, then you should be able to get that person to examine your physical setup and offer help in real time.

Any extra information would be helpful, screenshots of your Windows control panel settings, port address settings, are you using an add in card for parallel ports? etc..


Reply
cbell
Posts: 462
(@cbell)
Honorable Member
Joined: 18 years ago
dv3894 wrote:
Sometimes when I start the application and an error message says "The program is about to die..." What does that mean?

I suspect this isn't the problem in your case, but I was getting this error when my preferences file would get out of whack. I was using subversion to keep track of all my vixen files and make it so I could sync them across machines, and it would sometimes try and merge changes into the preferences file that it shouldn't have, thus making it invalid and causing Vixen to throw that error.

Deleting the preferences file usually fixed it for me, but then I had to reset my preferences in Vixen.


Reply
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago
dv3894 wrote:Thank you so much, that worked, but it only works with the printer port. The PCI cards are not being recognized by Vixen. And since my controller has two boards, we are only defeating half the battle. -- Thank you so much for your help, I am open to any suggestions.

You probably need to manually assign the port address in Vixen for the ports on the PCI board. In the Basic Parallel plug-in setup chose Other and manually enter the address for those ports. You can find what address they are using by going into the Device Manager and viewing the properties of your PCI device.


Reply
Posts: 34
Topic starter
(@dv3894)
Trusted Member
Joined: 17 years ago
RavingLunatic wrote:You probably need to manually assign the port address in Vixen for the ports on the PCI board. In the Basic Parallel plug-in setup chose Other and manually enter the address for those ports. You can find what address they are using by going into the Device Manager and viewing the properties of your PCI device.

In Vixen, at the plugin window, with the port setting open for the basic parallel plugin; I have choose each port name in the drop down box. The first selection works with the printer port, the second and third option do not work with any of the ports. Device manager states LPT2 and LPT3 are the PCI ports. LPT1 is the printer port.


Reply
Posts: 34
Topic starter
(@dv3894)
Trusted Member
Joined: 17 years ago
Aurbo99 wrote:

If you have 2.5 or greater, you may have to drop back to 2.1, there has been soem issue with the recent 2.5+ version.

ECP?, EPP? port settings? what are the port addresses?

Does the test program turn off and on the controllers?

Did you see it? and copy their setup? or just hear or read they have a similar setup? Important for troubleshooting.. If you actually saw it, then you should be able to get that person to examine your physical setup and offer help in real time.

Any extra information would be helpful, screenshots of your Windows control panel settings, port address settings, are you using an add in card for parallel ports? etc..

The test program only works when the controller is plugged into the printer port. I cannot change the port settings as far as ECP and EPP, because the card manually selects the mode 😡 the manual for the PCI card says "Build-in SPP, PS2, EPP, ECP compatible IEEE 1284 printer port." I know it works because I plugged my printer into it. As far as the setup, my setup is the same as his, just different port location. I followed his plans almost exactly, just built mine different. I have Vixen version 2.1.1.0.


Reply
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago
dv3894 wrote:In Vixen, at the plugin window, with the port setting open for the basic parallel plugin; I have choose each port name in the drop down box. The first selection works with the printer port, the second and third option do not work with any of the ports.

Yes, and there is a fourth option of Other which allows you to enter a port address for your port.

dv3894 wrote:Device manager states LPT2 and LPT3 are the PCI ports. LPT1 is the printer port.

You need to right click on the PCI ports and select Properties and then go to the Resources tab and you should see the values that they use for the I/O Range of that port. Use one of those values for the port address for the Other option.


Reply
Page 1 / 2
Share: