Multiple serial por...
 
Notifications
Clear all

Multiple serial ports

34 Posts
12 Users
0 Reactions
7,354 Views
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago
[#754]

I did some more testing today. I have 1 hardwired serial port and five USB to RS-232 ports.

When I run a 384 channel sequence with only one plugin using 128 channels, every thing is perfect.

Note: This is a continuous chase sequence with 50ms intervals, I chase 32 channel groups with each channel ON for 50ms. Vixen only sends new data if there is a change so you have to make a change EVERY interval to make it worst case.

If I add one more serial port, also with 128 channels, the serial data misses random channels on both ports. The hardwired and USB ports act the same. Can someone out there check this on their machine?

My machine is a 3.2 GHz Celeron with 2GB memory. During the sequence the HDD is NOT being accessed. The CPU load is around 24%. Memory being used is 216MB.


33 Replies
Posts: 339
(@dan-ross)
Reputable Member
Joined: 19 years ago

I'll have the rest of my REN-C parts tomorrow. I'll test this after I get them put together.


Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago

Well it looks worse. I configured one FGDimmer plugin for ony 32 channels. I then added 3 Renard Dimmer plugins with 64 channels each. With the same chase sequence, FGDimmer only got sent 4 good packets of data for every 32 packets that should have been sent.

I dimming is used (continously fade on and off) it just does not look smooth.


Reply
Posts: 705
 KC
(@kc)
Prominent Member
Joined: 20 years ago

Thanks for the specific numbers. Frank had previously reported a similar issue using five ports, which I don't have yet, but I do have two.


Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago

With two serial plugins configured, I have seen occasionaly a packet is not sent, it is random. I had to stare at one specific LED to see when it missed it's data packet (and Ernie made fun of me for having lights to tell you the lights are on!). They all miss a packet every once in a while while using two plugins.

Three was about the same. Four was over the edge of the cliff.


Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago
Dan Ross wrote:I'll have the rest of my REN-C parts tomorrow. I'll test this after I get them put together.

Dan did you get any testing done?


Reply
Posts: 339
(@dan-ross)
Reputable Member
Joined: 19 years ago

I'm hoping to test this week, either tomorrow night or the night after.

I did get as far as remembering to grab my usb to serial adapters from my desk in the office, now they are in my car.


Reply
Posts: 339
(@dan-ross)
Reputable Member
Joined: 19 years ago

Ok I'm playing with this now, from what I can tell it seems ok, but I only have 2 USB to serial and 1 built in serial. Can you post a copy of the sequence you were using and I'll try it with that.


Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago
Dan Ross wrote:Can you post a copy of the sequence you were using and I'll try it with that.

Here it is.........
(Vixen 2.0.3.3)


Reply
Posts: 861
 xmus
(@xmus)
Noble Member
Joined: 19 years ago

Do you guys ever deconstruct the vix file to see if Vixen constructed the channel information the way you think it should have? When i'm debugging a problem like this, i often do, but to KC's credit, i have not yet found a problem with Vixens translation from GUI to bit stream through the serial port....

Here is a perl script that does this (The code is really ugly, I basically brute forced the conversion, that has to be several other better ways to do this...)

http://www.ritzfam.com/ChristmasMadness/Prancer/


Reply
Page 1 / 4
Share: