Progress?
 
Notifications
Clear all

Progress?

52 Posts
10 Users
16 Reactions
3,511 Views
Posts: 397
(@billw)
Honorable Member
Joined: 16 years ago

What are those dark covers/areas on the seed pixels wiring that plug into the D3?


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

They're called Ferrule Connectors. The D3 connectors are insulation displacement (IDC) type but the Seed pixels have stranded wire. The strands would move during crimping and sometimes didn't connect or were a poor connection. The simple solution was to add a Ferrule Connector on the end. After some practice, I add the Ferrules in 10-15 seconds.

I ordered these from Amazon. You'll need a crimper, I ordered this one.


Reply
Posts: 849
Topic starter
(@tfischer)
Prominent Member
Joined: 17 years ago

Any reason you're diverging from the XConnect standard?

I'm guessing cost? Although the XConnects are pretty cheap during the group buy.

My early pixel stuff dating back to 2012 used a Ray Wu connector with a non-standard pinout (there either wasn't a standard yet or I didn't know what it was). The Ray connector is still viable but I fought that pinout for a long time, and that's why I've been using XConnect for all my newer stuff as well as moving over some of the old stuff. It's nice to be able to just plug something in and have it work.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I dont use xConnect or anything else. I use custom wiring on JST 3P connectors. I power inject every 25 pixels so I am cutting the wires anyway.


Reply
Posts: 849
Topic starter
(@tfischer)
Prominent Member
Joined: 17 years ago

> I power inject every 25 pixels

I'd switch to candles before I did that lol.

The only thing I currently power inject is my roofline.

My new canes will use a "power balancing"technique by passing the power straight through to the next connector so the power doesn't have to go up and back down the cane.

That's about it. 12V pixels rock lol.


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
tfischer wrote:
Any reason you're diverging from the XConnect standard?

I'm getting the D3 connectors for 20¢ each, even though JST SM connectors are cheaper. there is no soldering required though. Find me an xConnect close to that price.

I don't even bother to cover them. I've had JST SM connectors out in the open running a string of 10 WS2812B rings in modified lawn lights from sunset to sunrise every day for the last two years. They're also using a WLED controller that I link to xLights during both Halloween and Christmas display. No problems with the JST's, as long as they're not laying in a pool of water, though they are laying on the ground.

I figure the D3's will be the same, especially with the wider spacing.

tfischer wrote:
My new canes will use a "power balancing"technique by passing the power straight through to the next connector so the power doesn't have to go up and back down the cane.

I'm using 5-volt Seeds in a 105-foot string of 30, folded Seeds in 10-inch candy canes, 13 seeds per cane, placed along the edge of the yard. Power is only applied in the middle and the controller is on one end. The controller was powered by the string. This was another experiment at pushing the distance limit, for both wire and WiFi. These were 22-24 AWG Seed for the group buy three years ago. The failure point would have been the controller on the end but it always worked.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I have not had any water issues with the JSTs eiather. A bit of corrosionX gun oils every few year and they stay bright and shiny. Where I do have issues is in the JSTs not making good contact after 50 or so insertions.


Reply
Posts: 849
Topic starter
(@tfischer)
Prominent Member
Joined: 17 years ago

Group buy had 10 pair of xconnect pigtails (m and female x 10 each) for like 6 bucks. 30 cents a connector/60 cents per connection for a proven standard technology is a no-brainer IMHO.

But I've gone my own way on plenty of other things so I'm not knocking it.


Reply
Posts: 849
Topic starter
(@tfischer)
Prominent Member
Joined: 17 years ago

I've had xConnects/Ray Wus (they're the same basic technology) buried in snow, sitting in small puddles, etc etc since I started using them in 2012. I think I've had one or two issues out of several hundred connections in 14 seasons.

I'd never try that with JSTs


Reply
Posts: 849
Topic starter
(@tfischer)
Prominent Member
Joined: 17 years ago

(If there's one thing I've learned from social media is controversy builds engagement.

This forum needs more engagement, I've provided the controversy lol)
\


Reply
Page 2 / 6
Share: