Question on DMX
 
Notifications
Clear all

Question on DMX

9 Posts
5 Users
0 Reactions
2,430 Views
Posts: 13
Topic starter
(@mrdaddyhill)
Eminent Member
Joined: 13 years ago
[#35403]

**Warning total newb**

OK... So I've been looking around and I saw someone post this:

http://www.holidaycoro.com/27-Channel-DMX-Controller-for-RGB-Lights-12v-DC-p/24.htm

As a LOR alternative... If I understand correctly this will not work as it controls DMX RGB strips right? Or am I incorrect and each color channel could just be an individual channel that I could hook up to with female extension chord ends that I would then ground via bus or something like that? I hope this isn't a stupid question... But I did a search and couldn't find an answer... Thanks in advance!


8 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

That controller is used to drive RGB strips using a DMX dongle or interface. You would run some 4-conductor wire - usually at least 18 gauge or better from this to the strips.


Reply
Posts: 13
Topic starter
(@mrdaddyhill)
Eminent Member
Joined: 13 years ago

OK, so I was correct about that one... But I am wondering... Are there DMX controllers that would allow for each of the channels to become dumb channels instead of RGB? Does that make any sense?


Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago

MDH:

To restate Budude's answer (because it sometimes helps to hear two different people answer your question, not because my esteemed colleague is wrong):

That is a DMX-input device, so it takes a signal and converts it into voltage on and off (it does not output DMX). It outputs 12 volts on 27 channels; what you connect to that (as the chart at the bottom of the page shows) is any combination of dumb red-green-blue LEDs: either bullets, square format, rectangle format or strips.

If you connect a dumb RGB strip to this device (four wires), you use three channels and each LED will output all the same color(s). If you connect a string of dumb RGB pixels, it will again take four wires, using three channels, and all the pixels in the string all the same color at the same time.

HTH.

\dmc

PS: And Brian (Budude) and I are both concerned about this line " ... female extension chord ends ... " While you can use extension-cord-like wire, you don't use extension cords in low voltage environments, because you'll certainly mix them up with 120v extension cords and plug the low-voltage lamps into the high-voltage circuit, creating what we in the hobby call "the magic smoke."

PPS: Welcome to our madness.


Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago
MrDaddyHill wrote:OK, so I was correct about that one... But I am wondering... Are there DMX controllers that would allow for each of the channels to become dumb channels instead of RGB? Does that make any sense?

Oh, we posted at the same time.

The controller doesn't care what kind of load you're putting on each channel. One could be a yellow 12-volt incandescent lamp from your granddad's truck, another could be a white LED with the proper resistor installed and a third could be a group of six orange LEDs. The controller knows only electricity. What you define that electricity to do is up to you.

HTH.

\dmc


Reply
ksmith247
Posts: 418
(@ksmith247)
Honorable Member
Joined: 14 years ago
dmcole wrote:MDH:

PS: And Brian (Budude) and I are both concerned about this line " ... female extension chord ends ... " While you can use extension-cord-like wire, you don't use extension cords in low voltage environments, because you'll certainly mix them up with 120v extension cords and plug the low-voltage lamps into the high-voltage circuit, creating what we in the hobby call "the magic smoke."

PPS: Welcome to our madness.

This is so true. Take it from someone who made this mistake my first year of this hobby. Fried a PX1 and a strand of pixels doing just this.


Reply
Posts: 13
Topic starter
(@mrdaddyhill)
Eminent Member
Joined: 13 years ago
dmcole wrote:Oh, we posted at the same time.

The controller doesn't care what kind of load you're putting on each channel. One could be a yellow 12-volt incandescent lamp from your granddad's truck, another could be a white LED with the proper resistor installed and a third could be a group of six orange LEDs. The controller knows only electricity. What you define that electricity to do is up to you.

HTH.

\dmc

This essentially answers my question! Thanks 🙂

Also, thanks for the welcome! I did the "cheap" thing this year with a Gemmy 6 channel pre-programmed show as I was able to get it for only $40 allowing me to convince the wife that I could get bigger and better later on... What she didn't know was my plan was for the Gemmy one year then bigger and better the next year! lol Just looking at options for boards now... MUHAHAHAHA! lol


Reply
Posts: 5
(@bgmatth)
Active Member
Joined: 13 years ago

I have used this 27 channel controller. I have thought of the same.. I was going to use the controller matched up with some ssr's, this would give me 27 VAC connections. Only drawback, the system could not dim but only turn off/on.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
bgmatth wrote:I have used this 27 channel controller. I have thought of the same.. I was going to use the controller matched up with some ssr's, this would give me 27 VAC connections. Only drawback, the system could not dim but only turn off/on.

You can modify the existing AC SSR designs very simply to handle lower voltages (like 27 vac) by adjusting the gate resistors on them. I don't recall the exact resistor value change but it's a fairly trivial thing to do. That way you can use any of the various TRIAC output designs that already exist and fit into various enclosures. It would help with any resell down the road because you would just have to swap out the resistor to make them 120vac compatible...


Reply
Share: