Planning pixel matr...
 
Notifications
Clear all

Planning pixel matrix

6 Posts
3 Users
0 Reactions
2,582 Views
Posts: 7
Topic starter
(@shikimol)
Active Member
Joined: 10 years ago
[#49232]

Hi All,

I have been following this forum and Wiki for awhile now and must say that this site has alot of great information for someone wanting to get into anything to do with lighting and the control of them.

Now, I know that this is not really a xmas thing but it is still about controlling the pixels and powering them, so I am hoping that someone here will be able to just review what I have planned and let me know if I am on the right track.

Plans: Building a 48 * 24 RGB pixel matrix (1152 Pixels)
Controller: SanDevices E6804 (Purchased)
Pixels: RayWu 12v 30mA/per pixel WS2811 https://goo.gl/SgKsCC

Description:
Have spent sometime reading and learning as much as I can from the Wiki. Here is a description of what I have planned with an image to hopefully help.

As there will be 12v pixels @ 30mA = 34.56Amps all up. I have chosen a 12v 40Amp power supply to run the lights and the controller, as 32 is 80% of 40. So running the supply at about 82% give or take a little.

From the 12v i have chosen to use 10AWG cable and have two paths from the power supply, both with a 20Amp fuse. This then leads into 2x 8way fuse blocks.

Fuse block explanation:
I have split up the matrix into sections. Each 96 pixels will be power injection. This makes 13 Injection points all up plus 1 at the end of the matrix (14 points of injection).
Each 96 pixels is 2.88Amps, so I have opted to use 14AWG cable from the fuse block to the pixels.

So each fuse block will have 7 outputs to pixels with 3Amp fuses.
All + leads will linked and all - will be linked.

Is this the correct thinking I have been doing?

Outlay:

Layout

Cheers in advance,
Evan


5 Replies
Posts: 7
Topic starter
(@shikimol)
Active Member
Joined: 10 years ago

Thank's Mike,

I appreciate the reply. Good to know that I am on the right track. I will get back to the drawing board and look at the wiring again. Once I start building I will be sure to post the progress.

Thanks again.

Regards,
Evan


Reply
Posts: 86
(@onceler)
Estimable Member
Joined: 9 years ago
shikimol wrote:

Pixels: RayWu 12v 30mA/per pixel WS2811 https://goo.gl/SgKsCC

Just as a forewarning these pixels are NOT waterproof. So I would shy away from using them outdoors. The chips are exposed to the elements and will likely not fair well outdoors.


Reply
Posts: 401
(@kensington)
Reputable Member
Joined: 11 years ago
shikimol wrote:Hi All,

I have been following this forum and Wiki for awhile now and must say that this site has alot of great information for someone wanting to get into anything to do with lighting and the control of them.

Now, I know that this is not really a xmas thing but it is still about controlling the pixels and powering them, so I am hoping that someone here will be able to just review what I have planned and let me know if I am on the right track.

Plans: Building a 48 * 24 RGB pixel matrix (1152 Pixels)
Controller: SanDevices E6804 (Purchased)
Pixels: RayWu 12v 30mA/per pixel WS2811 https://goo.gl/SgKsCC

Description:
Have spent sometime reading and learning as much as I can from the Wiki. Here is a description of what I have planned with an image to hopefully help.

As there will be 12v pixels @ 30mA = 34.56Amps all up. I have chosen a 12v 40Amp power supply to run the lights and the controller, as 32 is 80% of 40. So running the supply at about 82% give or take a little.

From the 12v i have chosen to use 10AWG cable and have two paths from the power supply, both with a 20Amp fuse. This then leads into 2x 8way fuse blocks.

Fuse block explanation:
I have split up the matrix into sections. Each 96 pixels will be power injection. This makes 13 Injection points all up plus 1 at the end of the matrix (14 points of injection).
Each 96 pixels is 2.88Amps, so I have opted to use 14AWG cable from the fuse block to the pixels.

So each fuse block will have 7 outputs to pixels with 3Amp fuses.
All + leads will linked and all - will be linked.

Is this the correct thinking I have been doing?

Outlay:

Cheers in advance,
Evan

It will definitely work, but you’ve over-engineered the wire gauge unless you’re pushing power a long distance. You can also cut your injection points in half—inject every 192 pixels (or 4 rows). 12v pixels can easily go up to 110-120-ish before you really need to inject, and remember that current flows both directions from an injection point, so injection at the beginning, every 200 pixels thereafter, and the end is sufficient.

You can also reduce your power requirement by reducing brightness. You will be able to see that matrix from space at 100% power. I run my mega tree at 20% and it’s plenty bright even with two streetlights within 75 feet of it.


Reply
Posts: 7
Topic starter
(@shikimol)
Active Member
Joined: 10 years ago
onceler wrote:Just as a forewarning these pixels are NOT waterproof. So I would shy away from using them outdoors. The chips are exposed to the elements and will likely not fair well outdoors.

Hi Onceler,

Yes, I am aware that these are not waterproof. I am getting them as this pixel wall will be built in a housing and will be indoor use.
Thank you though for your reply.


Reply
Page 1 / 2
Share: