Planning next year....
 
Notifications
Clear all

Planning next year... help needed 🙂

4 Posts
4 Users
0 Reactions
1,679 Views
Posts: 8
Topic starter
(@grizli)
Active Member
Joined: 14 years ago
[#23469]

So I think our first year display went well (thank you DIYC), considering how late we started and everything.
We ran ren24 with just about 30 mins of show every night.

I would like to add more channels next year as 24 was just not quite enough, but I also am looking into smart rgb strings maybe to make couple/three arches or something along those lines.
So having said, I see a lot of people use DMX when it comes to s-rgb strings.
Can renard boards with used in line with dmx or is there a better solution?

I have over 1000 ft of extension cords just from 24hc, it would be nice to not have to double that if I go with 48 channels, are there other alternatives other than running power from controller boards? Something about external SSRs?

And last advise I need (at least for now :rolleyes:), what did you guys use to make FM frequency signs? We cut out numbers and letters in a box box with LEDs inside, but it's not as bright as I'd like next year's sign to be.
Thanks everyone


3 Replies
THurrle
Posts: 1211
(@thurrle)
Noble Member
Joined: 17 years ago

There are a number of controllers that use the ssr's and will cut down on the long runs of extension cords.
Here is a link that might give you some ideas. Dirk has a post that has a ton of info in it.
http://doityourselfchristmas.com/forums/showthread.php?24367-Conversion-to-Wireless&p=246624#post246624


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago
grizli wrote:So I think our first year display went well (thank you DIYC), considering how late we started and everything.
We ran ren24 with just about 30 mins of show every night. Congratulations!!!

I would like to add more channels next year as 24 was just not quite enough, but I also am looking into smart rgb strings maybe to make couple/three arches or something along those lines.
So having said, I see a lot of people use DMX when it comes to s-rgb strings.
Can renard boards with used in line with dmx or is there a better solution?
Start by refering to smart rgb as pixels. You don't need to switch your Renards to DMX. Just setup another plugin that uses E1.31 and your network card for the pixels

I have over 1000 ft of extension cords just from 24hc, it would be nice to not have to double that if I go with 48 channels, are there other alternatives other than running power from controller boards? Something about external SSRs?
Your ren24 is a great way to start. Now that you want to grow, get a Simple Ren32 or Ren 64 and a bunch of SSRs for your further out items and you may get by with very few extra power cords but will add cheaper network cables

And last advise I need (at least for now :rolleyes:), what did you guys use to make FM frequency signs? We cut out numbers and letters in a box box with LEDs inside, but it's not as bright as I'd like next year's sign to be.Thanks everyone

Search around this site and you'll find a dozen different methods for a sign. Don't limit your search to "tune to" but signs in general. You can take a welcome sign or Merry Christmas sign construction to your tune to sign. Bill from Florida has a nice pixel one with how to on his site or blog.


Reply
Posts: 18
(@m00987)
Eminent Member
Joined: 15 years ago

This thread shows how I made my pixel strip arches. They were very easy to build. I use E1.31 to run an E681, which drives my arches and some other pixels.

http://doityourselfchristmas.com/forums/showthread.php?24412-My-first-year-with-RGBs/page2


Reply
Share: