Odd Occurence
 
Notifications
Clear all

Odd Occurence

3 Posts
2 Users
0 Reactions
1,289 Views
Posts: 68
Topic starter
(@oyarsa)
Estimable Member
Joined: 5 years ago
[#55235]

I have a ready-to-run Falcon F16V4 kit. I am currently using ports 1-5 and not running all that much, really. The Falcon has a Meanwell 12v PSU powering it. Separate from that, I have another Meanwell for power injection. It is attached to a power distribution board from Wired Watts. Both the power supply and board are exposed. The power supply is on the floor of my garage and the distribution board was held a bit in the air because of the fairly stiff wire I am using. All of these were in my garage with wires running under the door. I run the show using an old laptop. The laptop and controller sit next to each other in a wagon with the FM transmitter on top of the controller enclosure.

Today we had a pretty big wind storm. The lights above my porch blew down. I went outside to repair them and I noticed that one of the lights on the distribution board was no longer lit. I figured a fuse had blown. This happened once when I was originally putting up that set of lights and they fell. I assume that somehow the falls create a short somewhere, but I'm not sure where/how. Since I had received an enclosure for the distribution board, I unplugged the power injection wires and put everything in the enclosure. I used a new spot on the distribution board for the power injection wires for the porch. Nothing shorted out. I started to run a test with the show. Everything worked, but I had a hard time seeing the lights. I assumed it was because it was bright daylight and considered it a job well done.

Tonight, I left the house on an errand and noticed the lights seemed a lot dimmer than I remembered. I thought that maybe the lights had previously been running at 100% (using ZCPP, I had dimming curves intended to limit to 40%) and after something I had done, it was now running at the appropriate 40%. But, I was still curious, so I pulled up the controller page as I was heading out of the driveway via remote desktop. I noticed that the second temperature sensor was reading 206 degrees! This seemed very odd to me since the first temperature sensor was at 87 degrees. This was causing the show to run at 5% brightness. Which, interestingly, was still about as bright as the neighbor's lights. I was concerned, so I headed back up the driveway and opened the garage door. When I got to the laptop, it still showed around 190 degrees but seemed to have dropped some. I moved the FM transmitter (which wasn't hot to the touch) off the controller box and the temperature dropped further. I opened the controller box and the temperature continued to drop until it was matching the 1st sensor. I put my hand over the board and couldn't feel any residual heat. Once the temperature dropped, the lights went back to the 40% they should be at (at least, as far as I can tell with ZCPP). Everything seems to be running perfectly fine now. But I'm wondering what caused the high temperature/high reading.

Could an FM transmitter interfere with the sensor? It was sitting on the right side, where I assume the 2nd sensor might be and while the temperature went down when the garage door opened, the biggest change appeared to be when I moved the transmitter. Could it be a short or something somewhere that isn't blowing a fuse, but actually is causing the board to overheat? The way it rapidly decreased in temperature (over the course of seconds) makes me think that the reading was false. What does the 2nd sensor monitor exactly? If the reading was truly accurate, what could have caused it? Any thoughts/suggestions?


2 Replies
Posts: 242
(@rsegreto)
Reputable Member
Joined: 6 years ago

So I had my FM transmitter too close to my controller initially and it made it go crazy! Mine is a Kulp K8-PB but basically it knocked out the wifi and the controller was unresponsive when I tried navigating using the onboard buttons and oled screen. I moved the transmitter away and that seemed to fix the issue for the most part.

However I have still found that if I have my controller bootup when the FM transmitter is turned on it still knocks out my wifi and for some reason changes the audio output settings to dummy. If I let the controller bootup and then plug the FM Transmitter in I didn't have any issues. My fix now was to put them on separate timers.

One other note might be your two PSU's. You mentioned that you are using one to power the controller and therefore the first pixels in your strings and then another for PI. Did you also cut the V+ lines at your PI location? If not then the PSU's voltage might be fighting each other and potentially cause the excess heat. When you PI with a separate PSU you need to make sure the V-'s are connected but the V+ needs to be cut or separated.


Reply
Posts: 68
Topic starter
(@oyarsa)
Estimable Member
Joined: 5 years ago

Thanks for the suggestions. I did disconnect the V+ at the power injection sites. But, I didn't exactly isolate the two sides of the clipped wire. Just clipped it. So maybe one of them was making a connection somehow and the slight bit of movement was enough to jostle them apart.

Any other possibilities? Or should I just keep an eye on the situation and assume it was either the transmitter or a fluke?


Reply
Share: