i pulled the trigger and im working on my first small display. however im looking for some suggestions on placement of things below. I have attached my drawing/measurements and a pic of the house from the street for visual reference.
I started out with the plan to only do arches this year but as i play with this stuff im already thinking of just expanding to a few other things. I already built 4 leaping arches that i planned to use with a small H008 controller and power supply to do some random effects however if i get a big controller in time i will probably add them to it.
Now the unplanned Phase 2 for this year i need a little help with.
I am mounting WS2811 pixels along the 1st story on the left side of the house and then jump over to the Garage roof line. (yellow highlights in the attachment)I planed to put my Rasp Pie 3 inside the left hand side of the garage door and then run cat 5 and a power cord out to a Controller. Im really leaning towards the new Falcon based on what i read. I thought about the smaller 4 channel one but at $120 i thought i might as well get the bigger one for $80 more and have room to expand. With the thought of a mega tree next year i wondered if im best to place the Falcon and Power out in the yard to shorten the wire running out to each item. My plan is to keep the house bullets up all year so those wires id like to hide. I can snake some wire under the vinyl siding on the house if it helps hide it. I can also go up the corner posts.
Already have :
Pie 3
350 watt power supply
WS2811 pixels to do the 2 outlines mentioned in either 2 or 3 inch spacing.
mounting strips to mount them under eave edge.
Misc connectors.
- Should i go 3 inch spacing or 2 inch along roof lines?- Eventually i will add strings where you see other measurements like the 2nd story but spacing that out for cost and time 🙂
- If i get the Falcon does it hurt the board if i only power half of it up this year since i wont have a need for all the ports?
I dont have a problem staking the controller somewhere in the mulch just for the Oct - Jan time frame or for a more permanent placement i could attach it to the side of the steps going to the front door. If i put the Mega tree approx 25 ft from the controller, is that to far to run the wires out to it?
I also thought about putting the controller at top or bottom of the brick face on the left side of the garage. This makes house outline wires easier but then i have to run more wires across that sidewalk to the front door for arches and Mega tree, its just a little more visible there.
If i get the Falcon I will probably throw some pixels on those 2 bushes in front of the house this year also.
Thoughts on any of this is much appreciated.
No attachments.
I didn't notice they failed due to the size. Thanks for letting me know.
- Should i go 3 inch spacing or 2 inch along roof lines?- Eventually i will add strings where you see other measurements like the 2nd story but spacing that out for cost and time 🙂
Our houses are similar. I am using 3" spacing. I think 2" would be overkill. These lights are bright at full power. You'll still have to turn them down at 3".
- If i get the Falcon does it hurt the board if i only power half of it up this year since i wont have a need for all the ports?
No, it won't hurt anything. Just make sure you are within the power capabilities if you are pulling all you power from the board directly.
I dont have a problem staking the controller somewhere in the mulch just for the Oct - Jan time frame or for a more permanent placement i could attach it to the side of the steps going to the front door. If i put the Mega tree approx 25 ft from the controller, is that to far to run the wires out to it?
You really want the controller as close as possible to where you connect to the pixels. That would be a lot of long wire runs to a megatree. Think about a another controller just big enough to run the megatree rather than trying to run everything from a centrally located controller. You have to worry about signal loss and voltage drop when you start talking about that kind of distance. It means bigger wires and maybe some null pixels to boost the signal.


