Skunberg wrote:
2. I'm concerned about how much power the fan motor use's and the electrical noise of a motor may have bad effects, light misfires, extra fires, bad timing, ect.
Interesting. That will sway me away from using a channel to inflate. Bummer. I've seen other shows inflate with a channel. I'm 99% sure that was a light-o-rama set up though. Would the electrical noise not have an impact in a light-o-rama setup?
Art wrote:...have some channels left for future expansion:grin:
This is where I am the most confused. I think because I don't quite have a grasp on actual cost to build a ren24ss with enclosure compared to a central board with external ssr's. That is what I need to look into. If there is a cost sheet floating around somewhere please link me to it!
I've done some looking myself... And everyone will be different. It all depends on ext. cords, ssr's, controllers, set-up. They way one might set it up is probably not the way someone else would. I've been over and over different set-ups and decided that I will just use whatever comes up in coops at a decent price. I have my layout basically done however I'm still questioning the controllers. My issue is that somethings I plan I cannot devide by 4 (for ssr's) and I just can't see putting 2 ssr's there and have 2 channels un-used. So like said it is just going to depend on what you plan.
smoothice wrote:Interesting. That will sway me away from using a channel to inflate. Bummer. I've seen other shows inflate with a channel. I'm 99% sure that was a light-o-rama set up though. Would the electrical noise not have an impact in a light-o-rama setup?This is where I am the most confused. I think because I don't quite have a grasp on actual cost to build a ren24ss with enclosure compared to a central board with external ssr's. That is what I need to look into. If there is a cost sheet floating around somewhere please link me to it!
I build a ren24 last year and i believe i spent between 60 and 80 on parts plus the board. and the parts for the ren64 is 60 plus shipping plus the board. for the ssr's you can buy them from a coop or you can make your own. parts for each ssr is about 5 or 6 dollars for four AC channels;)
I've design some SSR"s where i daisy-chain them, two channels per box and they will fit into a regular plastic recepticle box.
smoothice wrote:Interesting. That will sway me away from using a channel to inflate. Bummer. I've seen other shows inflate with a channel. I'm 99% sure that was a light-o-rama set up though. Would the electrical noise not have an impact in a light-o-rama setup?
LOR should be affected the same as Renard. Just because they did it doesn't mean they didn't have noise if the motor would generate it and if it would affect the controllers.
You could also run a separate power line for the motors and have each motor on a separate SSR controlled by a wall wart witch is switched on and off by the controller.
See here for an example, I just jumpered the +5v source to the control line and plugged my wall wart(+5v dc) in to the controller, I also added a barrel jack to the board instead of the terminals so that I could change out my wall wart more easily if it ever went bad.
This is where I am the most confused. I think because I don't quite have a grasp on actual cost to build a ren24ss with enclosure compared to a central board with external ssr's. That is what I need to look into. If there is a cost sheet floating around somewhere please link me to it!
Ask and ye shall receive: Comparison of DIY Boards
Jrd wrote:Ask and ye shall receive: Comparison of DIY Boards
Thanks. I had found that page once before but not knowing at all what I needed it was not very helpful. Now it is golden!!
are those giant lights inspired by Old Navy?
remixsam wrote:are those giant lights inspired by Old Navy?
Why yes, yes they are 🙂
smoothice wrote:Which is cheaper? To build a system with 1 controller and a ton of extension cord or a system with many controllers and less extension cord?
Keep in mind that cost isn't everything. A distributed system is probably going to be a bit more expensive, BUT, how much is your time/sanity worth?
Having all of your cables coming from a centralized controller for your setup is going to drive you nuts.
Entropy wrote:Keep in mind that cost isn't everything. A distributed system is probably going to be a bit more expensive, BUT, how much is your time/sanity worth?Having all of your cables coming from a centralized controller for your setup is going to drive you nuts.
Agreed. Also the less visible wire the happier my wife will be.
