Display Extension C...
 
Notifications
Clear all

Display Extension Cords

11 Posts
8 Users
0 Reactions
3,522 Views
Posts: 14
Topic starter
(@dennis-v)
Eminent Member
Joined: 12 years ago
[#31745]

Hello Everyone

I wanted this to be my first light show, but just realized that the extension cords would be out of my range. My home is built on the back part of a 1 acre lot with lots of trees. The house cannot be seen from the road & the only alternative is a small clearing on the lot that can be seen, however it is 150' from the house & I assume I would one cord per channel.

I was planning on using 72 channels but making extension cords for each channel would be to costly for me at the moment, since I am retired & money is kind of tight. I was planning on a display with the following.
1-8' Mega tree running 24 channels.(this will be the main display) 4-mini trees running 4 channels each & 3 arches running 2 channels each, making it 46 channels. Is there any cheaper way to power the channels? Any help would be appreciated.

Thanks
Dennis


10 Replies
Posts: 352
(@maffeirw)
Reputable Member
Joined: 19 years ago

If you position your controllers at the display site, depending on your power requirements, you may be able to run one or two 15 amp extensions cords (mine are home built of 12g Romex) to controllers and run short extension cords from the controllers (or run the MegaTree strings directly to the controller). That’s what I currently do with my 20 ft 96 channel MegaTree. One 15 amp extension cord provides more then enough power to light all 96 LED light strings at once (at 5w a string that's still less than 500w total). You'll have to do the math to determine how much current your setup needs.
Ron


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

Thats why the low channel coun controlers are nice you can have one cord feeding the controllers then 8 or more channels very close to the lights my stuff is generally within 6ft of the controler.


Reply
Posts: 928
(@arw01)
Noble Member
Joined: 13 years ago

Yep, as suggested, put the controllers out by the display (hid it behind or under something else or in the middle of the megatree on the pole). Then you just need a long set of extension cords and a long control cable to the controller.


Reply
Posts: 14
Topic starter
(@dennis-v)
Eminent Member
Joined: 12 years ago

Thanks a lot guys, I found an aluminum case in my junk pile which is fully insulated inside with thick rubber & waterproof lid. I will be using 4 Renard ssr-24 boards & put them in the case & hide it in the display. One thing I would like to know is what output on the computer would be best to run the controller over that distance or is the cable from the computer limited.

Thanks Again
Dennis


Reply
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 20 years ago

You will want to use RS485 to the first Renard.


Reply
Posts: 1120
(@4586shaggy)
Noble Member
Joined: 14 years ago

or just run your show off a Raspberry Pi, u have audio/video and the sequences coming out of a credit card sized computer that u can schedule just like your show computer. no data connection from the house needed (as long as u add an onboard clock). This way u just have to worry about 2-3 extension cords, and u wont have to worry about the range on your fm transmitter since it will be right by the display.


Reply
Posts: 231
(@jmksparks)
Reputable Member
Joined: 18 years ago

Or even XBEE to XBEE that is what I am using. Show computer indoors little xbee antenna by window out to Renard ss,s.


Reply
Posts: 230
(@rtrip9)
Reputable Member
Joined: 13 years ago

I would suggest what they are saying or even better pixels. More channels less wattage. Run cat5 out there. And 1 power cable to the 12v converter. A lot more options with pixels.


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

I would suggest you keep it simple. Get a rs485 adaptor for the pc and use vixen2/3, HLS, or what ever program you want.
http://www.ebay.com/itm/USB-to-RS485-FTDI-interface-Board-for-Power-One-Aurora-Inverter-Web-Data-Logger-/131224128750?pt=LH_DefaultDomain_0&hash=item1e8d914cee

You will also want a cat5 cable to go from your pc to the controler, any size and color you want.:) YOu cut one end off and attach 3 of the wires to the above adaptor chack the wiki for help, if you cant figure it out we are all here to help.
http://www.monoprice.com/Search?cp_id=10208&keyword=cat5


Reply
Page 1 / 2
Share: