Good evening all..
I started this all last year and had to make a break from it. I had an awful time just getting my head around everything. So I put things away for a while and last month broke out the box and started retracing my steps.
What I did figure out that using Vixen with the Arduino mega board and Sain Smart 16 channel board was part of my tragedy in failure. I dont have a lot of C++ and what little I know is about that far from scary screwing things up.
So in my research I have figured out the least amount of c++ is going to a renard board and there is my next issue is I am a contractor that swings a 30 oz hammer and a soldering gun with electronics may be my next demise.
Anyone have any advice to offer the sausage fingered man on how to create the boards I will require and what boards will give me the best opportunity for expansion without starting completely over again. I can see that this may be my best avenue at this point with vixen being more compatible with the renard system as far as I can tell
Some guidance and what ever advice will be greatly accepted.
Thanks
Bryan
you might wanna see if someone has a board for sale being this late in the season and not having soldering skills
Yep, see if you can find some that someone else already soldered up. Many people these days are switching over to pixels and want to get rid of their Renard gear. That's how I've gotten all but one of my controllers this year. But the prime time for this type of acquisition is after Christmas, not right before.
Try posting a WTB (Want to Buy) post and see what comes up.
Jimboha
Welcome back. I almost pulled the trigger on my first show this year but I held off and the bug has bitten again so my first show will be 2016.
You are kind of up against it to do much this year so try not to put yourself under too much pressure. Taking the time out to learn and plan what you want to do gives you plenty of time to research and plan out. Of course, you could tinker with what you have so far and get a feel for things.
As Jimboha says, many people are leaning towards pixels nowadays so you could end up spending twice if you decided to switch down the road. Soldering is not too difficult. I presume there are many guides online and with a little practice, I'm sure you would pick it up. Pixel controllers can be purchased pre assembled so soldering could be limited to joining strings, adding connectors etc.
Good luck :thup:
You can look at some of the ready made controllers like those from Falcon or or Sainsmart.
I will be selling most of my renard stuff after this years display. I have 11 24ch renard controllers.
How many channels of Renard do you need? I'm not going to get all of mine out again, so I might as well start moving some to a home where they will get used.
I tried the arduino 2560 board with the slain smart 16 Chanel switch boards. I could get the switch and board to work when I downloaded a test program onto the board. Every time I tried vixen it would fail to communicate with the switch or board I tried a number of times until I gave up and ran test through Christmas.
I guess what i am asking is what is the best for the entry level guy ? I don't want to get into pixels yet until I can figure out the basics ( would like to keep my hair for a little longer) I know that pixels are where things are going but I can do what my thoughts are with led strings and built displays that will keep the wife happy. I will adventure into pixels after I can get to this point.
What boards would you recommend that will work with vixen 3 .
I have a friend that I talked to today that can help me with the soldering and fabrication as needed.
I did the mega board and the slain smart switches by a recommendation by a you tube video. Now I am open to any suggestions to help me get along my way as I know that I was so in over my head with the c++ and knowing that I don't have a great back ground in it made my life struggle too much.
Any direction would be nice
As for the channels I was attempting a start with 16 Channels to begin with and didn't succeed there. I would like the opportunity to expand a bit in the near future as I get it working.
Thanks
Bryan
Sent from my iPad using Tapatalk
Bryan with the renard boards you can find them in 8 16 24 ch controllers and you can daisy chain (Link) them together with a simple Ethernet cable like I stated earlier you should buy one that someone has finished and it is working so you can get a start on a show this year since Christmas is so close then next year you can easily add too it with another renard board or pixel controller
welcome back to the world of bright lights!
i'm using arduino..yes it was a hassle to get around to things to make it work..but with the help of everyone on the forum i got to see what my sequences looked like for the first time last year,this is going to be my second year...atleast you started with ssr's i started my first year using a 16ch mechanical relay board with an arduino mega and man that was a bad idea,this year i'm using 16 4ch ssrneon relay boards and 2 arduino megas totaling 64 channels...i don't have knowledge of c++ either..i just used whatever code i could find online that works with the setup i have..:razz:
