EDM Set up
 
Notifications
Clear all

EDM Set up

18 Posts
6 Users
0 Reactions
6,961 Views
Posts: 6
Topic starter
(@ed-faranda)
Active Member
Joined: 12 years ago
[#47545]

I got a EDM transmitter, because i have read it is one of the best. However, I am having issues with it and was hoping someone could help me. I am sure it is something I am doing. I am getting poor quality tramission.

My EDM is mouned in CG-1500 box.. With a Pi Contoller. I have the audio output connected with a Sound Blaster PLAY 3.

The antenna out is connected to an RCA cable, converted to a BNC, exits the box to a BNC to RF Cable, then ran to a 75 to 300 ohm converter to a 1/2 Wave Dipole antenna, mounted to my mega tree pole in vertically.

I have a feeling something is wrong with my setup is the reason why I am bad quality audio out of my transmitter. It has poor range and poor signal.

Any suggestions??!?


17 Replies
rstehle
Posts: 4348
(@rstehle)
Illustrious Member
Joined: 19 years ago

I don't use any sort of impedance converter with my EDM. Take the 75 to 300 ohm converter out of the circuit and see if that helps.


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I also do not use a 300 ohm converter. Not sure why you would need it. Also, the EDM is 50 ohm output. You need to be running 50 ohm wire from the EDM to the antenna and then just hook up the antenna.


Reply
sporadic
Posts: 1199
(@sporadic)
Noble Member
Joined: 14 years ago

As others stated, I would use 50 Ohm cables and connectors throughout the RF chain. Inside a mega tree isn't exactly the best place either for a dipole. What kind of issues are you experiencing though outside of range? Is it audio quality, distortion, hum, sibilance, etc..?


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

+1, especially on where you have it mounted and the 50 ohm cable issue.
Your antenna needs to be as much in the clear as possible.
Also, how long is your coax from the transmitter? How far is the transmitter from the show controller?

sporadic wrote:As others stated, I would use 50 Ohm cables and connectors throughout the RF chain. Inside a mega tree isn't exactly the best place either for a dipole. What kind of issues are you experiencing though outside of range? Is it audio quality, distortion, hum, sibilance, etc..?

Reply
Posts: 6
Topic starter
(@ed-faranda)
Active Member
Joined: 12 years ago

It sounds like I have these completely hooked up incorrectly.

My EDM is just a few inches away from my Pi Controller, in the same CG-1500 box. I am attaching some pictures. From the sound of things, I need to move my antenna off the mega tree, using a 50 ohm cable. Does anyone recommend a good 50 ohm cable? Where would I get one (amazon?).

IMG 2903

Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Might I ask where you got the antenna? 300 ohms on an antenna is something you get with the store bought FM receiver antennas (little wires coated in plastic). Those do not work well as transmission antennas.


Reply
Posts: 6
Topic starter
(@ed-faranda)
Active Member
Joined: 12 years ago

Audio quality, distortion, slight hum...


Reply
Posts: 6
Topic starter
(@ed-faranda)
Active Member
Joined: 12 years ago

I got it from DIY LED Express... You have an antenna you recommend?


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

While you find a cable, I'd also suggest you put a ferrite bead on the power cable into the EDM if there isn't one already.

RE: where to get the cable: In the past, we'd all tell you to go to radio shack, but that ship has pretty much sailed. Everything is on ebay and amazon,
its just a matter of how long you have to wait. Also, don't get a lot more cable than you need. If you need 20 feet and can only find a 50 foot cable,
you should also order a new BNC connector and shorten the cable.

You should also edit your profile and list your location as someone close to you may have an extra !

ed.faranda wrote:It sounds like I have these completely hooked up incorrectly.

My EDM is just a few inches away from my Pi Controller, in the same CG-1500 box. I am attaching some pictures. From the sound of things, I need to move my antenna off the mega tree, using a 50 ohm cable. Does anyone recommend a good 50 ohm cable? Where would I get one (amazon?).


Reply
Page 1 / 2
Share: