EDM Buzzing
 
Notifications
Clear all

EDM Buzzing

28 Posts
7 Users
0 Reactions
10.7 K Views
Posts: 215
Topic starter
(@reelpilot)
Reputable Member
Joined: 12 years ago
[#42462]

I'm having an issue with constant buzzing coming from my EDM transmitter. When I'm playing music through it sounds great most of the time. However at both the beginning and ends of songs when the volume tapers, you start to hear a buzzing sound. Then if I have no audio playing, such as during a pause between songs, the buzzing is quite loud and annoying. I saw a similar thread, but in that instance the buzzing was only present when connected to a FPP. For me, I have buzzing with the audio coming from the FPP, my iPhone and even with no audio source and the cables removed from the EDM. There is a note in the EDM manual that says humming may occur if 100mW is selected. Mine is selected to 10mW, if I select it to 100mW the buzzing increases, but only marginally. I have tried powering the EDM from various wall warts as well as my Meanwell power supplies. The wall warts were the same and the Meanwell was noticeably louder. I'm using the short antenna I bought with it from EDM and have also tried the test antenna with no change in the buzzing.


27 Replies
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

With any transmitter that isn't powered from a battery you will almost always need to do something to eliminate the hum that is generated by the power supply.

I know of two things that can help a lot.

1. A ferrite bead on the power input into your transmitter. You can get a clamshell type that snaps onto the line. My transmitter would be terrible without this modification.
2. Get a Wall Wart Tamer. This is a passive filter capacitor approach that will also clean up a power signal.
http://renard-shop.com/other-boards/14-wall-wart-tamer-kit.html

My suggestion is to try the ferrite bead and if that isn't satisfactory, then buy the wall wart tamer. Often you can get the ferrite bead for free. They often come with new TVs and other electronic equipment or you can remove them off old power/network cables.

My wiki entry on the FM02 has some good pictures:
http://www.doityourselfchristmas.com/wiki/index.php?title=Vastelec_FM02#Do_you_have_a_HUM_.3F


Reply
Posts: 215
Topic starter
(@reelpilot)
Reputable Member
Joined: 12 years ago

Thanks for the suggestions. I'll try these and report back.


Reply
Posts: 259
(@cmschleich)
Reputable Member
Joined: 11 years ago

Ferrite core with 4 wraps of the power cable didn't help. I unplugged all the audio and notice my humm is coming from the transmitter itself. Maybe a higher quality power supply? I'm using the one EDM sent, which doesn't look that special.

I guess I need to try with a battery.


Reply
Posts: 215
Topic starter
(@reelpilot)
Reputable Member
Joined: 12 years ago

I powered my EDM off a battery and had no change with the buzzing sound. Like Cmschleich, my buzzing sound is coming from the EDM itself with or without audio input. I don't have any spare ferrite beads around the house, so I'll have to try that another time.


Reply
Posts: 215
Topic starter
(@reelpilot)
Reputable Member
Joined: 12 years ago

I emailed EDM and reported all the troubleshooting steps I have done thus far. They suggested unplugging the RDS chip to see if that was the source of the problems. Unfortunately the buzzing was still the same with the RDS chip removed and EDM wants me to send my transmitter in for service.


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Good to hear they are going to service the unit.

reelpilot wrote:I emailed EDM and reported all the troubleshooting steps I have done thus far. They suggested unplugging the RDS chip to see if that was the source of the problems. Unfortunately the buzzing was still the same with the RDS chip removed and EDM wants me to send my transmitter in for service.

Reply
Posts: 259
(@cmschleich)
Reputable Member
Joined: 11 years ago

Test tonight with a 12VDC battery didn't improve it for me either. Mine just arrived 2 weeks ago, how long have you had yours ukewarrior?


Reply
beeiilll
Posts: 869
(@beeiilll)
Prominent Member
Joined: 19 years ago

Just chiming in here with my experience with my EDM.
I have had mine since 2008. It is a plain LCD unit before RDS was available. I did have some noise problem at first but it was the power supply and a new one cured it completely.
I do get very faint buzzing/noise during quiet passages but not noticeable to most anyone at either the 10mw or the 100mw settings.

I would have EDM check the unit and make sure it is okay since it is new. They are a very good place to deal with and have always been great to deal with although I have never had to send a unit back to them. I can only say that I am more than impressed by the quality of the EDM unit and the service and correspondence with the company.

Not much help I know but hopefully you two can get your units taken care of quickly.


Reply
Posts: 215
Topic starter
(@reelpilot)
Reputable Member
Joined: 12 years ago

I heard back from EDM and they said that my transmitter checked out normally and they were using my power supply and antenna that I sent in with the unit. They even attached an audio clip of the EDM in which they indicated, "during the silent pieces where audio was muted to the EDM, you can only hear the normal system noise floor." So apparently the buzzing that I am hearing is what they attribute to normal noise. At a low volume level that noise is not very noticeable, but at moderate and higher volumes, it does become quite noticeable when the music has quieter moments. Their suggestion is to use an external antenna such as the j pole and get the transmission away from the EDM. http://www.jpole-antenna.com/shop/low-power-fm-lpfm-broadcast-antenna/


Reply
Page 1 / 3
Share: