Splitting a PVC pip...
 
Notifications
Clear all

Splitting a PVC pipe

78 Posts
32 Users
0 Reactions
86.9 K Views
ChristmasBuddy
Posts: 452
Topic starter
(@christmasbuddy)
Honorable Member
Joined: 14 years ago
[#21114]

I am planning a project where I will need to cut a PVC pipe in half. But not what you are thinking. I need to split it in half length (from end to end) so I end up with two full length halves.

If I had a table saw then I know I could do it but the only tools I have is a jig saw and a circular saw. I also have a Dremel. The pipe has a one inch diameter.

Any thoughts?

Thanks!


77 Replies
Christmas Mark
Posts: 42
(@christmas-mark)
Trusted Member
Joined: 14 years ago
UBotBuddy wrote:I am planning a project where I will need to cut a PVC pipe in half. But not what you are thinking. I need to split it in half length (from end to end) so I end up with two full length halves.

If I had a table saw then I know I could do it but the only tools I have is a jig saw and a circular saw. I also have a Dremel. The pipe has a one inch diameter.

Any thoughts?

Thanks!

Try Laying the pvc on a flat surface and clamping pieces of wood along the length, level with the top of the pipe and then use the circular saw, this will be easy or hard to do depending on how long your pvc pipe is. I have done this for different projects, and its somewhat of a pain but it does get the job done, just go slow. Good Luck!!:biggrin:


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
UBotBuddy wrote:I am planning a project where I will need to cut a PVC pipe in half. But not what you are thinking. I need to split it in half length (from end to end) so I end up with two full length halves.

If I had a table saw then I know I could do it but the only tools I have is a jig saw and a circular saw. I also have a Dremel. The pipe has a one inch diameter.

Any thoughts?

Thanks!

Even on a table saw it is a very difficult thing and not safe. If you use a saw, you will not end up with two halves anyway. The Width of the blade will remove that much of the pipe. I assume there's not a cost savings thing since 1" PVC is very inexpensive.

I would find a router and build a jig. The jig doesn't have to be the full length, but maybe 2-3 feet long. Very simply jig that will enable you to clamp the pipe to it and also allow you to remove the top half of the pipe. If you can't get a router then I would still build a jig that you can use with the circular saw. Do not try and save both haves. There's very little value in that and a great deal of additional risk. The last option is for you to do the same thing with the dremel with some sort of Rotozip type blade/bit. Cutting through one side at a time.

Maybe you could tell us what you are trying to make and we can provide alternatives. I tried to cut a 2" PVC pipe on my table saw. It got bound up in the blade and was kicked back towards me at a high speed. It brushed off my head, but two inches to the left and I'm convinced that my wife would have found be dead on the shop floor. Be Careful and work safe!


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
Christmas Mark wrote:Try Laying the pvc on a flat surface and clamping pieces of wood along the length, level with the top of the pipe and then use the circular saw, this will be easy or hard to do depending on how long your pvc pipe is. I have done this for different projects, and its somewhat of a pain but it does get the job done, just go slow. Good Luck!!:biggrin:

I just saw this after posting mine. This can work, but don't free-hand it. Attach some sort of fence to the bottom of the saw to be used as guide. It would be just a little bit thicker than the wide of the pipe and as wide as possible to provide a good base. It would be attached so that the blade leaves you with a complete "half" I still recommend not trying to save both haves.


Reply
ChristmasBuddy
Posts: 452
Topic starter
(@christmasbuddy)
Honorable Member
Joined: 14 years ago

The pipe is about 48 inches in length. I thought about that method but I don't have wood that length. I would love to flip my circular saw on its back BUT that is highly dangerous.


Reply
Page 1 / 16
Share: