Generating DC volta...
 
Notifications
Clear all

Generating DC voltage

18 Posts
6 Users
0 Reactions
7,589 Views
Cheater
Posts: 114
Topic starter
(@cheater)
Estimable Member
Joined: 17 years ago
[#10271]

How do some of you guys generate DC for running LEDs?

Right now I've got one LED string which seems to like somewhere between 14v and 18v (wall wart says 24v - it isnt).
5 more in the mail which probably will want something different.

I intend to be getting only LEDs, and I will more than likely be buying them opportunistically so different sets with different requirements.
No I'm not making it easy on myself I know. :p

Right now my idea is computer psu supplying 12v. Cheap and simple.
Then I'm thinking of making a generic adjustable buck/boost switching regulator board which I can power off the psu, and adjust it for each string of lights.
That way I can just make a bunch of them, put the regulator board out where they are being switched and just run 12v everywhere.

I am starting from scratch (0 lights at the beginning of this year) and I have the knowledge required to design something like this.
The question is are there other ideas people have for supplying DC?
I know the vast majority of the stuff here is AC based.


17 Replies
Posts: 114
(@tabor)
Estimable Member
Joined: 18 years ago

Before answering your question are you sure the plug pack is not producing 24V AC. Most light strings in Australia run a 24 V AC.

How are you measuring the voltage from the plug pack?
If with a multimeter are you on the AC setting?


Reply
Posts: 604
(@aussiephil)
Honorable Member
Joined: 19 years ago

Cheater

Same question, how are you measuring that voltage, i'd be suprised if the unloaded voltage was lower than the rated voltage on the outside.

As to your question, I just buy SMPS from here
http://cgi.ebay.com.au/27V-DC-13A-350W-Regulated-Switching-Power-Supply_W0QQitemZ370311936942QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item56384fbbae
they have various voltages.

If your going DC then some advice, settle on one or two voltage levels and either buy all your lights to suit or be prepared to make them suit the voltage. trust me it is far easier in the long run.

I run 14k of lights, mixed inc and LEDs all from DC at 28v and 48v this year with the other 2.5k i had being 240v AC

The rare 18v stuff is not used to i can modify the strings.

Oh btw, nearly all xmas LED's sold this year at 24v seemed to require 26v to 30v DC to achieve 20mA per section of LED's.

Cheers
aussiephil


Reply
Cheater
Posts: 114
Topic starter
(@cheater)
Estimable Member
Joined: 17 years ago
Tabor wrote:How are you measuring the voltage from the plug pack?

Actually you just made me go re-read the wall wart. I read 24 the first time but its actually 18.

aussiephil wrote:As to your question, I just buy SMPS from here

$50 AUD for 350W is surprisingly good actually. I'll keep that in mind.
A computer psu is cheaper but you do need to boost it back up.

I'll see what the next batch of lights use and figure it out then. 🙂
Its just good to know that DC is used a bit since nearly everything here is about AC.


Reply
Cheater
Posts: 114
Topic starter
(@cheater)
Estimable Member
Joined: 17 years ago

Attached is a picture of a computer PSU with a boost regulator attached.

$20 350 watt power supply gives 16A of 12v and 20A of 5v which is more than enough to power lights and the logic circuitry respectively. 🙂
A few bucks worth of parts gives me a range of 15v - 50v with a few amps.
Mind you it started whining at 45v. I'll mainly be using it at 24v.
Also the inductors I've got cant exactly take a lot (hence why there are 3 of them). I'll be making a few boards of these and sourcing proper inductors from Mouser.

04022010744

Reply
Page 1 / 4
Share: