Wiring up controlle...
 
Notifications
Clear all

Wiring up controllers and pixels

21 Posts
13 Users
0 Reactions
5,755 Views
Posts: 86
Topic starter
(@onceler)
Estimable Member
Joined: 9 years ago
[#48109]

I've looked at the site and wiki many times and limited suggestions about what types of wires to use for sending data, and power to the controllers and pixels.

It seems the suggested route is an 18awg wire for power? Then cat5 for data?

How do people run those?


20 Replies
rstehle
Posts: 4348
(@rstehle)
Illustrious Member
Joined: 19 years ago

All of this technical mumbo jumbo can be confusing, especially to a newer member. In this case, it is the cable from the controller to the Pixels that is being discussed. Most folks either use 3 conductor 18 ga. 'pixel' cable, OR Cat5 (or 6). 18 ga. is great for short runs, under 10'. Cat5/6 is great for longer runs. In either case, the power and data is carried on the same cable.


Reply
Posts: 401
(@kensington)
Reputable Member
Joined: 11 years ago

Distance is a factor in both data and distance. For power, you need heavier gauge wire for longer runs, as voltage starts dropping off with distance. I try to keep power supplies within about 30 feet of the pixels, although my longest run this year was in the 40-foot range.

If your controller is more than about 20 feet from the first pixel, you need (a) null pixels to refresh the data, (b) a line driver, or (c) Cat 5.


Reply
Posts: 86
Topic starter
(@onceler)
Estimable Member
Joined: 9 years ago
rstehle wrote:All of this technical mumbo jumbo can be confusing, especially to a newer member. In this case, it is the cable from the controller to the Pixels that is being discussed. Most folks either use 3 conductor 18 ga. 'pixel' cable, OR Cat5 (or 6). 18 ga. is great for short runs, under 10'. Cat5/6 is great for longer runs. In either case, the power and data is carried on the same cable.

I think that makes sense for data. But power most cat5 is thin and I believe wouldn't be good for passing power from the psu to the pixels.

Sent from my Nexus 6P using Tapatalk


Reply
stallionent
Posts: 1460
(@stallionent)
Noble Member
Joined: 13 years ago

Here's a color chart showing how power and data is connected

Cat6 Colors

DMX + is data, DMX - tied to ground


Reply
stallionent
Posts: 1460
(@stallionent)
Noble Member
Joined: 13 years ago
Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I use 16AWG wire for power and cheap 20AWG wire for data. I also put in a NULL Pixel / buffer driver every 15'. If I used a higher quality cable such as CAT5 or CAT6 for the data, I am told I can easily reach 40' without a null pixel or buffer driver. I do not do this in my show o I cannot verify the distance.

For power, when the distance from the supply to the pixels exceeds 15' I use a higher voltage and then drop the voltage at the insertion point using a buck conveter. Having a 12v line lose 2v and then convrting to 5v means the LEDs always get full voltage. You can do the same with dropping 24v to 12v for 12v pixels.


Reply
stallionent
Posts: 1460
(@stallionent)
Noble Member
Joined: 13 years ago

My longest run of CAT5e is a little less than 50 ft., with no null pixel/buffer driver. I believe I could go much longer.


Reply
Posts: 740
(@ezellner)
Prominent Member
Joined: 11 years ago

To add another variation, I use 14 gauge speaker cable for power and 18 gauge stranded wire for data. I use 5 Volt pixels (3500 pixels total). My longest power run is about 40 feet and my longest data run is about 35 feet. I do not use null pixels although I do have some on hand should there ever be issues. I have not had any issues with either power or data using this configuration.


Reply
kk6ou
Posts: 108
(@kk6ou)
Estimable Member
Joined: 10 years ago

I tried running about 25' with 16AWG and using CAT6 for data and still could not get GECE to work. I ended up having to put the PS next to the pixels. Apparently they are more sensitive to voltage drop.


Reply
Page 1 / 3
Share: