I suggest you get the ratcheting tool. It works so much better than the un-racheted tool. I have a ton of connectors from 12 gauge to 24 gauge including the cavity plugs. Those are the waterproofing seals on the end. They differ in size corresponding to wire size. When I first used mine I didn't crimp the cavity plug on at the same time. That didn't work out too well. And don't forget to get the removal tool. Shop around for a heavier gauge removal tool. The light aluminum ones tend to bend easily. I got mine at an auto parts store.
Sent from my SM-T710 using Tapatalk
Craiz, you mentioned using pigtail connectors from diyledexpress and other automotive weatherproof connectors and that the connectors you have tried were not very good. What issues have you run into with the diyledexpress pigtail connectors and extensions? I just pre-ordered a bunch of them to use throughout my display this year and thought it would be better to have the connectors for easier setup and teardown and storage. Thanks.
ReelPaws wrote:Craiz, you mentioned using pigtail connectors from diyledexpress and other automotive weatherproof connectors and that the connectors you have tried were not very good. What issues have you run into with the diyledexpress pigtail connectors and extensions? I just pre-ordered a bunch of them to use throughout my display this year and thought it would be better to have the connectors for easier setup and teardown and storage. Thanks.
Here are some things I don't like about the connectors I've used:
Generic Automotive Weatherproof Connectors
- Not very weatherproof resulting in corrosion
This may very well be user error.
- Sometimes difficult to get the pins aligned when plugging them in. This has resulted in breaking a couple pins. The pins I had for 18ga wire where very thin/flat. They do have some plastic alignment inserts but those don't seem to always work well.
- No easy pin release mechanism. I was able to successfully remove one broken pin to repair/replace, but on the other two broken pins I ended up damaging the connector body so much that I just replaced the whole thing.
- Locking clips break very easily.
Pigtail connectors (2-3 pin)
- Cannot choose/configure the wire size
- Sometimes difficult to align the round plugs when connecting
Wire size is really the main issue driving my consideration of not using the pigtail connectors. Additionally, having a bunch of connectors and raw wire gives more flexibility to create whatever wiring I need rather than ordering specific lengths of wiring with connectors. If I could get them for a reasonable price in larger gauge wire (12-16) it would make it an easier decision to go with them go with them. Especially with having connectors already attached to the strings. I'm going to add 24 24" boscoyo snowflakes and some arches to a long section of green arborvitae trees I have along the side of my property. It would be nice to hook them all up with data and power injection using premade wires and connectors but I'd also like larger gauge wire for power.
I'm considering a hybrid approach where I build the snowflakes to use the attached 3-ping connectors for the data path and splice in a Delphi 2-pin connector at the beginning of the string to optionally inject power. If I go that route though, I think I might as well just use the Delphi connectors for all of it.
Anyone have a good source of a flat 3 conductor wire?
craiz wrote:Anyone have a good source of a flat 3 conductor wire?
I've been looking up 2 wire and 3 wire sources and options. I ultimately am planning 3 wires for everything and using just 2 of the 3 wires for power injection when needed. That way I don't have to worry about mixing 2 and 3 wire setups throughout. But, in my research, here's some sources I've found. You should be able to find other gauge wiring at these sites.
18awg 2 wire - $65 for 500 feet (unshielded) ($0.13 per foot)
https://www.wireandcableyourway.com/belden-6300ue-18-awg-2-conductor-unshielded-cmp-plenum-security-cable.html?gclid=CNj9-6TZsdECFRtXDQodKeQJig
18awg 2 wire - $55 for 500 feet (unshielded) ($0.11 per foot)
https://www.wireandcableyourway.com/Low-Voltage/Security-Alarm-Cable/CMP-Plenum-Stranded-Unshielded/18-2c-cmp-plenum-security-cable-stranded-unshielded.html
18awg 2 wire - $78.99 for 500 feet ($0.158 per foot)
http://www.monoprice.com/Product?p_id=13730
18awg 2 wire - $109.99 for 1000 feet – black sheathing ($0.11 per foot)
http://www.monoprice.com/Product?p_id=13730
18awg 3 wire - $23.49 for 100 feet ($0.235 per foot)
http://www.holidaycoro.com/100ft-3-Conductor-18-AWG-Extension-RGB-Lights-p/696-100.htm
18awg 3 wire - $36.50 for 250 feet ($0.146 per foot)
http://www.holiday-light-express.com/RGBwireplugs.php
If I purchase any bulk 3 wire cable, will likely purchase from holiday light express.
I want to use 12/2 landscape lighting wire like this for power injection with the Weatherpack connectors. I've got a bunch of it from some landscape lighting projects. I see there are connectors available for 12ga wire but I've got a couple questions I'm hoping someone with experience with these connectors can answer. Will the cavity seal work on the thick insulation of this kind of wire? Think I could get by with a 14-16ga rated crimper? The only 12ga crimpers I can find are a bit more than I'd like to spend (~$90 example).
