Using bullet node p...
 
Notifications
Clear all

Using bullet node pixels for icicle lights

51 Posts
15 Users
0 Reactions
20.6 K Views
Posts: 311
(@neilric99)
Reputable Member
Joined: 17 years ago

latest design I have with Ray Wu is for a 3-4-5 drop set of 12mm ws2811 12V nodes 10cm spacing in white wire and 15cm spacing between drops for 1.8M lighted length (48 nodes per set). This is so that I can easily join 2 sets together without additional power injection required and if more than 2 are joined then I will power inject every 2 sets to maintain the whites. I am contemplating if I would need the drops to be in sets of 3-4-5-4.

arw01 wrote:Thinking of custom Ray setup too. Been buying some tube dripping lights from ace Hardware for two years on the sales. I have 5 sets of 24 tubes now and could maybe fit 5v ws2812 down each with data return. Keep hoping someone does a pcb with a data return to the list top!

Sent from my Sony Tablet S using Tapatalk


Reply
rfallatt
Posts: 648
(@rfallatt)
Honorable Member
Joined: 16 years ago

Why not 6-4-5-3 (3 inch separation ) for a 1 ft section

Sent from my iPhone using Tapatalk


Reply
Posts: 311
(@neilric99)
Reputable Member
Joined: 17 years ago

I have a single level home and 2ft drop would be too much. however I am sure that Ray Wu can custom make any layout that you need. and not for much more than the regular node price.


Reply
Posts: 853
Topic starter
(@roterhead)
Prominent Member
Joined: 15 years ago

This closer to what I was thinking of. Does your design with Ray have an equivalent length wire returning back up the drop, then feeding across the spacing?

So, in other words:

Lead in wire - 3 pixel drop (3*10cm) + approximately 33 cm (return) + 15cm spacing +
4 pixel drop (4*10cm) + approximately 44 cm (return) + 15cm spacing +
5 pixel drop (5*10cm) + approximately 55 cm (return) + 15cm spacing
repeat 3 more times + lead out wire.

The return wire could be zip tied to the down drops using white zip ties or possibly a short piece of white shrink tube (since these are custom anyway).

Might be better to randomize the lengths within the sets and not have a strict visual repeating lengths. Perhaps like: 4 - 3 - 5 - 4 - 5 - 3 - 3 - 5 - 4 - 5 - 3
Or perhaps different random length sets that could be plugged in to help the random factor.

Maybe a small get together buy for better pricing... I would probably be looking at 30-35 of these sets. Yeesh, that's around 1700 pixels. Good thing I'd be using 24V supplies with buck convertors...

Thoughts?

neilric99 wrote:latest design I have with Ray Wu is for a 3-4-5 drop set of 12mm ws2811 12V nodes 10cm spacing in white wire and 15cm spacing between drops for 1.8M lighted length (48 nodes per set). This is so that I can easily join 2 sets together without additional power injection required and if more than 2 are joined then I will power inject every 2 sets to maintain the whites. I am contemplating if I would need the drops to be in sets of 3-4-5-4.

Reply
Posts: 114
(@grump010)
Estimable Member
Joined: 17 years ago

Ray is happy to build custom strings, I created a version from Leechburg Lights Youtube video. Can be seen here.

RGB Icicle lights

When complete the icicle at the top of each drop will be zip tied at 5cm (approximately 2") from the first node and this will make a 20cm 7.9" spacing between each drop.


Reply
Page 4 / 11
Share: