trouble with sandev...
 
Notifications
Clear all

trouble with sandevices e682

24 Posts
5 Users
0 Reactions
5,429 Views
Posts: 224
Topic starter
(@mrlights2000)
Reputable Member
Joined: 19 years ago
[#52183]

hi I have finally built and powered up my sandevices e682 and im not getting all the yellow leds to light as per manual. I have voltage in all the test spots except at j21 pin 2 and 1. in the trouble shooting guide it say feel for hot parts but im not feeling anything hot. im missing the top yellow led (3.3V) in the build manual it say for version 1.3 (what I have) place a shunt on j26 the eeprom ic I cant place a shunt cause it has a part unless this means flipping boards over and placing a cut off from a resistor or something between those two bottom pins of that part

I did get a head of myself and solder all the parts on the board before doing the needed pre-test...…

any help would be appreciated

thanks, danny


23 Replies
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Do you have power to both sides of the board? Check your fuses. If you're powering the board and pixels with 12 volts make sure you have jumpers correctly on J21, jumper across 1-2 and 3-4.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 224
Topic starter
(@mrlights2000)
Reputable Member
Joined: 19 years ago
pmiller wrote:Do you have power to both sides of the board? Check your fuses. If you're powering the board and pixels with 12 volts make sure you have jumpers correctly on J21, jumper across 1-2 and 3-4.

Sent from my SM-T710 using Tapatalk

Yes power on both sides fuses are all fine


Reply
Posts: 224
Topic starter
(@mrlights2000)
Reputable Member
Joined: 19 years ago
pmiller wrote:Do you have power to both sides of the board? Check your fuses. If you're powering the board and pixels with 12 volts make sure you have jumpers correctly on J21, jumper across 1-2 and 3-4.

Sent from my SM-T710 using Tapatalk

Voltage at j3&j4 is 12v j1&j2 nothing


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

All my 682's are version 1.3 and do not require a shunt. You have something else going on.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 503
(@iflights)
Honorable Member
Joined: 14 years ago

Post a relatively high-resolution photo of the component side, and the solder side of your E682? I can compare against my spares.


Reply
Posts: 224
Topic starter
(@mrlights2000)
Reputable Member
Joined: 19 years ago
iflights wrote:Post a relatively high-resolution photo of the component side, and the solder side of your E682? I can compare against my spares.
image0
image1
image2

Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

I hope your propeller chip doesn't fail. Unsoldering 40 pins is laborious unless you have a desoldering tool. There should have been a 40 pin socket supplied with the 682. I would check all your soldering. It looks like some could use some extra attention. I had that issue even though the solder looked good it was a pin on the propeller socket that was bad. There should have been sockets supplied for the 16 pin chips also.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 224
Topic starter
(@mrlights2000)
Reputable Member
Joined: 19 years ago
pmiller wrote:I hope your propeller chip doesn't fail. Unsoldering 40 pins is laborious unless you have a desoldering tool. There should have been a 40 pin socket supplied with the 682. I would check all your soldering. It looks like some could use some extra attention. I had that issue even though the solder looked good it was a pin on the propeller socket that was bad.

Sent from my SM-T710 using Tapatalk

Yea I was thinking the same but there wasn’t a 40 pin socket holder in my kit thought that was a bit odd. Didn’t think anything of it and just solder it on prob not my smartest idea I guess the excitement got the best of me.

Sent from my iPhone using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
MrLights2000 wrote:Yea I was thinking the same but there wasn’t a 40 pin socket holder in my kit thought that was a bit odd. Didn’t think anything of it and just solder it on prob not my smartest idea I guess the excitement got the best of me.

Sent from my iPhone using Tapatalk

You should have contacted Jim at Sandevices. He would have sent them out right away. Keep that in mind.

Sent from my SM-T710 using Tapatalk


Reply
Page 1 / 3
Share: