Technicolor quality...
 
Notifications
Clear all

Technicolor quality?

256 Posts
45 Users
0 Reactions
83.3 K Views
dsmjuggalo
Posts: 663
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

I am losing these at about 3-4 per day now. I have 5 right now that are staying lit blue when they get power so it's only a matter of time before these go too. I'm running a 682 with a converted atx power supply. At what point should I be requesting a refund on these junky pixels. I bought 5 strands of these and have had at least 5 bulbs fail on each strand. I had 25 extra bulbs and those are gone. I am now just shortening strings on window frames just to keep lights running. I don't understand how some people have 5 times the amount I have with zero failures yet I have at least 30 failures.


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

Re: Technicolor quality? Latest update

Hi All,

Well, Ray and I had a nice long talk last night so I though I'd update you on the current status with the updated pixels, why we think, actually know, why there were so many problems and why some have had no problems at all.

The biggest problem with the pixels were something that Ray had no control over. World Semi produced a bad run of WS2811 chips and World Semi admitted to this being a problem. The had serious issues which showed up as various failure modes. Some of the modes just looked dead but still passes data to the next pixel in line, some were total failures and the signal stopped at that pixel, and some caused very high currents to pass through the LDO and the chip which fried the works. I don't know what arrangement Ray has with World Semi as far as how much of the production cost they will reimburse him so I won't speak to it.

A lesser issue was moisture getting into the pixels. Normally is a little moisture gets in it won'e hurt anything since the PCB are conformal coated. The problem was they part of the production run did not get coated. Ray didn't even know that until well after they had been sent out. I won't get into details other than to say if I was Ray at least one head would roll.

Design problem. There was one design issue that I brought to Ray attention several weeks ago and that was no input and output resistors. That has been corrected on the new PCB design. Most of the time the missing resistors would not cause any major issues and when it did it was mainly on longer lines from the controller to the first pixel. it was possible that the input could be driven outside the maximum rating but usually this would happen during hot plugging. Whit the new PCB this should not be an issue.

Wiring changes. As I have said with the new PCB came a wiring change on the cable. The new order is DATA, GND, +12V. This keeps the data lines away from the +12V which is a good thing. However there is one thing you will have to watch out for if you're cutting strings. The new wiring order is between pixels however the wiring between the connector and the first and last pixel is still using the original order. When the pigtails are installed they wiring will be swapped. As I said this only effects you if you cutout the first or last pixel. If you cut anyplace in the string the order will be DATA, GND, +12V.

Also I've ask Ray to modify the mold so that a small raised dot will be on the opposite side from the direction arrow. This will identify the newer pixels. I've also ask Ray to modify the mold with inserts so he can change the identifier, part number, so future changes such as a pixel based on the TM1829 or some other design can be identified easily. When this happens it will replace the small dot identifier.

Pixel string colors. Ray can do Green and White strings. This includes the wire, body and the cover ring. I told him that he'll likely sell more green and white that black once he puts those colors into the lineup. I don't think the prices will be any different but that's not a promise. What we would like to know is what shade of Green would be the one to use? Personally I think it should be about the same as normal christmas lights which I think is called Winter Green but I need to check that out. We'll go over this more just after the first of the year.

I don't think I've forgotten anything at least anything I can disclose. I do know that these bad pixels hit Ray very hard, he told me how much but I won't pass it on, and I hope that World Semi covers most of Rays losses. I will say that other manufactures have likely gotten those bad WS2811 so they could show up anywhere including the other Pixel line that used here. You just don't know unless you can read the manufacture date on the chip, I'm going to try and get that date range, and if the chip is not visible you won't know unless you rip the pixel apart. Even my more than 800 pixels could be effected as batches of the completed boards were mixed with good ones during assembly. Since I've only lost one pixel I've told Ray that well take care of me once he has everyone else taken care of.

If Ray was a lesser man he might have just packed it in but he really is trying to do right by his customers. I really feel for Ray on this one.

John


Reply
Posts: 14
(@keitha43)
Active Member
Joined: 16 years ago

Re: Technicolor quality? Latest update

What about the TM1804 strands that also failed miserably for the people who bought them? Steve Gase was one.


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

I didn't talk to Ray about them. I'll ask when I take next time.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

I'm sure Ray took a major hit here and there but he needs to know that if he can deliver a rock solid product at a decent price that he will have more biz than he knows what to do with...


Reply
Page 24 / 52
Share: