Broomy111 wrote:This post said with the Falcon board the guy got out 100ft to the first pixel- http://doityourselfchristmas.com/forums/showthread.php?42123-Falcon-vs-E682/page3Sent from my iPhone using Tapatalk
This is what was posted:
"The F16v2 is in a league of its own right now. With the newest developments coming out with distances of 100' to the first pixel...your be doing yourself a huge disservice purchasing anything but the F16v2"
He didn't say it does, he said it will when the new board comes out.
However, there are posts where guys have claimed 60+ feet. I've don't it, but I've done on the Falcon and the PixLite.
If you haven't bought a board yet I would highly suggest you get the Falcon. Spend the extra few dollars and get the best.
James
Sent from my SM-G900V using Tapatalk
Either way, It will make a nice addition to my hardware
Sent from my iPhone using Tapatalk
Just wondering if you guys have seen that Advatek Lights actually already make boards very similar to these. They have been selling them since late last year. Here is the text off there site & link for those interested.
Long Range Controller; https://www.advateklights.com/shop/mantis-pixel-mapping/40-pixlite-16-controller.html
Receiver Boards; https://www.advateklights.com/shop/mantis-pixel-mapping/42-pixlite-16-controller.html
The PixLite16 controller converts Art-Net or sACN (E1.31) data via an ethernet connection to pixel data for driving LED pixel lighting.
The PixLite Long Range sends the data up to 300m+ distance and is converted back to a pixel ready signal at the other end by these small receiver boards. The long distance signal is sent using a differential pair which elimates the typical problems seen in pixel systems (crosstalk, signal degradation, reflections, etc) which otherwise prohibit pixels being installed far from the controller. The PixLite Long Range also eliminates the need for null pixels.
The controller uses standard Cat5 cables to transmit the signals. Any standard network cable can be used for the connection between PixLite Long Range Controller and these Receivers.
The controller can operate in 2 modes:
Mode 1: Normal - Each receiver drives 2 pixel outputs of any supported pixel type. The controller uses all 8 output jacks.
Mode 2: Condensed - Each receiver drives 4 pixel outputs of any DATA ONLY pixel type. I.E. If the pixels only have a data line and no clock (like the WS2811 protocol), the receivers can drive 4 sets of pixels at the same time. The controller uses only the first 4 output jacks to send all 16 output channels.
It supports the following input protocols:
-sACN (E1.31)
-Art-net
It can handle up to 32 universes of Multicast/Unicast E1.31/Art-Net data and controls up to 340 pixels on each of the 16 outputs.
It is also capable of simulataneously outputting 4 DMX512 universes (acting as a E1.31 to 4 x DMX512 bridge, no Art-Net to DMX) in addition to the 32 universes of pixel output.
Outputs to the following IC types:
TLS3001, SM16716, LPD6803, WS2801, WS2811, WS2812, WS2812B, TM180x, MBI6020, APA102, INK1003, MY9231.
The controller also interfaces with our GUI utility for easy configuration and uploading of new firmware.
Cheers
Doug
AussieDoug wrote:Just wondering if you guys have seen that Advatek Lights actually already make boards very similar to these. They have been selling them since late last year. Here is the text off there site & link for those interested.Long Range Controller; https://www.advateklights.com/shop/mantis-pixel-mapping/40-pixlite-16-controller.html
Receiver Boards; https://www.advateklights.com/shop/mantis-pixel-mapping/42-pixlite-16-controller.htmlThe PixLite16 controller converts Art-Net or sACN (E1.31) data via an ethernet connection to pixel data for driving LED pixel lighting.
The PixLite Long Range sends the data up to 300m+ distance and is converted back to a pixel ready signal at the other end by these small receiver boards. The long distance signal is sent using a differential pair which elimates the typical problems seen in pixel systems (crosstalk, signal degradation, reflections, etc) which otherwise prohibit pixels being installed far from the controller. The PixLite Long Range also eliminates the need for null pixels.
The controller uses standard Cat5 cables to transmit the signals. Any standard network cable can be used for the connection between PixLite Long Range Controller and these Receivers.
The controller can operate in 2 modes:
Mode 1: Normal - Each receiver drives 2 pixel outputs of any supported pixel type. The controller uses all 8 output jacks.
Mode 2: Condensed - Each receiver drives 4 pixel outputs of any DATA ONLY pixel type. I.E. If the pixels only have a data line and no clock (like the WS2811 protocol), the receivers can drive 4 sets of pixels at the same time. The controller uses only the first 4 output jacks to send all 16 output channels.
It supports the following input protocols:
-sACN (E1.31)
-Art-netIt can handle up to 32 universes of Multicast/Unicast E1.31/Art-Net data and controls up to 340 pixels on each of the 16 outputs.
It is also capable of simulataneously outputting 4 DMX512 universes (acting as a E1.31 to 4 x DMX512 bridge, no Art-Net to DMX) in addition to the 32 universes of pixel output.
Outputs to the following IC types:
TLS3001, SM16716, LPD6803, WS2801, WS2811, WS2812, WS2812B, TM180x, MBI6020, APA102, INK1003, MY9231.
The controller also interfaces with our GUI utility for easy configuration and uploading of new firmware.
Cheers
Doug
I know plasmadrive uses them. You may ask him what he thinks.
James
Sent from my SM-G900V using Tapatalk
