Notifications
Clear all

Roofline pixels

39 Posts
17 Users
0 Reactions
13.7 K Views
dsmjuggalo
Posts: 663
Topic starter
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago
[#44339]

What is everyone using for roofline pixels? Strip is out of the question as I want actual bulbs. I've ran pixabulbs for 3 years now with maybe 1 or 2 failures but this year they are dropping like flies. Out of the 119 on my roof I've probably replaced 20. Didn't really like how the 5050 led in them never matched the colors of the bullet and square nodes I use elsewhere anyways.

Sent from my iPhone using Tapatalk


38 Replies
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

I use pixabulbs. I've only had one failure on the rooftop. The ones on the ground along the driveway seem to fail much more often. But I'm still nowhere near the 20% you're reporting. I'm starting to attribute that to the fact that they're facing up, and they get all the snowblower abuse.
I haven't found them to not match colorwise. They look dead on with all the other 8mm nodes I'm using.


Reply
dsmjuggalo
Posts: 663
Topic starter
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

Mine are all facing up as well. We've had a lot of rain this season and all of my failures have came on rainy days so I'm sure it's water intrusion. I've had these pixabulbs since the very first presale on them and this is my first issue. The color has always been slightly off but the whites aren't even close. The pixabulbs are more a 3000k white and the others a 5000k

Sent from my iPhone using Tapatalk


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

the ones on my roof are not facing up. I have them facing forward. the only ones I have facing up are along the driveway and gardens on the ground. So maybe it's the facing up part that contributes to water failure. The ones along my driveway are also from that very first presale batch. Maybe it's just their time to go.
The color though seems to have everything to do with power. If they're getting too much voltage drop, they'll definitely start to shift toward the warmer end. But if they've got a good solid voltage, the white is very close to that 6500k "rgb white"


Reply
Posts: 598
(@nutz4lights)
Honorable Member
Joined: 17 years ago

I use Ray Wu's technicolor bulbs. Videos are located at the link below. I am one of those old fashioned nuts that really likes the classical look of a true c9 bulb on the roof. I had the technicolor v1 bulbs that failed. Ray replaced those for me with the technicolor v2 bulbs that failed. I was one of the folks that helped Ray troubleshoot their manufacturing failure. He moved away from injection moulding the base to an epoxy filled setup. Because there wasn't another bulb comparable, i had Ray replace the v2 with the v3 at no cost to me. They have performed perfectly for two years now. 400 bulbs not a single failure.

I tested the pixabulb at some point and although it was nice, it is simply not a c9. I suppose if the epoxy filled technicolor bulbs didn't work, i would have considered using the pixabulb, but they DID work and i didn't have to compromise.

Let me know of any questions.

Louie

Sent from my SM-G928V using Tapatalk


Reply
Posts: 2
(@jmjordan)
New Member
Joined: 15 years ago

I have had good luck with Pixabulbs so far. I used 160 of them mounted facing out last season with no failures. This year I had 600 Pixabulbs on my house and roofline, all mounted pointing out, and another 350 bordering my yard, in speed stakes facing up. I only had 1 Pixabulb failure this season, in my yard border, from water intrusion after a hard rain.

-Mark


Reply
Posts: 192
(@rdj6107)
Estimable Member
Joined: 11 years ago

louie i was looking at your videos. what spacing is your pix-a-net? 2" or 3"??


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago

I use Ray's bullet pixels with Ray's C9 covers pressed unto them. All facing up and held up with Home Depot gutter/tile clips.

In 2 years I've not lost a single roof pixel.


Reply
Posts: 375
(@gocats7)
Honorable Member
Joined: 18 years ago
deonb wrote:I use Ray's bullet pixels with Ray's C9 covers pressed unto them. All facing up and held up with Home Depot gutter/tile clips.

In 2 years I've not lost a single roof pixel.

Do the covers fit tightly and if not how did you hold them together. I have read they are quite loose. Also, do you have a video showing them?

Sent from my Pixel XL using Tapatalk


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago
gocats7 wrote:Do the covers fit tightly and if not how did you hold them together. I have read they are quite loose. Also, do you have a video showing them?

They are insanely tight. My wife pushed them on with a vise-grip. She's still complaining how her hands hurt - 2 year later.

There are the ones I'm talking about:
https://www.aliexpress.com/store/product/faceted-White-C9-covers-with-screw-for-technicolor-pixel-100pcs-set/701799_1328883482.html?spm=2114.12010608.0.0.sszq0x

They're threaded, but on a bullet we obviously don't use the thread since it's a friction fit on the inside instead. But still - there's no way they'll come out spontaneously.

They're still up on the eaves so I can' take a video of them yet (unless you mean you want to see them up on the eaves... but they just look like any other C9 lights).


Reply
Page 1 / 4
Share: