Tegbert wrote: http://falconchristmas.com/wiki/index.php/Pi_RequirementsSays there you need a usb memory stick. If I am not mistaken the sd card is the operating system and the stick hold sequencing info and music files and such.
Travis
Yes, that is for the overall requirements, to use; not to install. These are the official instructions, for installation 😉 But no matter, I have the secret sauce now, so should be good to go.
Sd card is the os and the FPP software. I have 4 raspberry pi's in my show. All 4 have the same image on the sd card. Music, video,sequences and config info are on the USB flash drive. My USB cards are 32gb, my sd cards are 8gb. I have two projectors in my show. Video synced to the sequence. Considering that the falcon Pi player is just 1 1/2 years old, it is amazing what it can do. Each FPP can drive 64k channels.
smeighan wrote:Sd card is the os and the FPP software. I have 4 raspberry pi's in my show. All 4 have the same image on the sd card. Music, video,sequences and config info are on the USB flash drive. My USB cards are 32gb, my sd cards are 8gb. I have two projectors in my show. Video synced to the sequence. Considering that the falcon Pi player is just 1 1/2 years old, it is amazing what it can do. Each FPP can drive 64k channels.
When can we see video of your display? Both in front and behind the scenes? 🙂
Thanks,
-joni-
I got FPP installed. The RPI is currently working, running FPP, with eth0 attached to my router, and my e682 controller board is also attached to the router. There is also an internet connection. The RPI is at 192.168.1.200. The e682 controller is 192.168.1.206.
I have have been able to bring up the e682 controller page and the FPP page and have done some tests. I have also ran some sequences (with FPP page) and have set a program schedule, and it executed properly.
However, I really prefer not to have my RPI attached to any computer at all. I'd like to be able to attach my e682 directly to the RPI and have it play the program. I'm almost positive this is possible. But I haven't been able to figure out what the magic is.
I went through the same steps of setting up a program schedule, then just connected the RPI to the e682 but it didn't play the program as scheduled. Perhaps there is some setup for this I missed. I have it set for Standalone.
1) Can the RPI be connected directly to the e682, and not require any internet or computer, other than the Ethernet cable between RPI and e682?
The other thing I'd like to do is to run a program or sequence, directly upon powering, and not rely on a time schedule. Is that possible? How?
MikeSD wrote:I got FPP installed. The RPI is currently working, running FPP, with eth0 attached to my router, and my e682 controller board is also attached to the router. There is also an internet connection. The RPI is at 192.168.1.200. The e682 controller is 192.168.1.206.I have have been able to bring up the e682 controller page and the FPP page and have done some tests. I have also ran some sequences (with FPP page) and have set a program schedule, and it executed properly.
However, I really prefer not to have my RPI attached to any computer at all. I'd like to be able to attach my e682 directly to the RPI and have it play the program. I'm almost positive this is possible. But I haven't been able to figure out what the magic is.
I went through the same steps of setting up a program schedule, then just connected the RPI to the e682 but it didn't play the program as scheduled. Perhaps there is some setup for this I missed. I have it set for Standalone.
1) Can the RPI be connected directly to the e682, and not require any internet or computer, other than the Ethernet cable between RPI and e682?
The other thing I'd like to do is to run a program or sequence, directly upon powering, and not rely on a time schedule. Is that possible? How?
Yes, don't need the computer hooked up. But honestly I would put the PI wifi on your personal network, so that you can control it and put the eth0 from the Pi and the E682 on their own private (single ethernet link network), that way you have full management of the Pi, but the show will be unimpeded by your local lan traffic . Another bonus is that the PI can keep time sync by using the WIFI to get it's NTP information. (kind of important when running things on a schedule).
And on the boot question, you can run a cron job that starts a playlist, but I don't see why this is needed with the scheduler available?
Tory

