# pixels per output...
 
Notifications
Clear all

# pixels per output - 5A != 100+ pixels?

21 Posts
12 Users
0 Reactions
7,696 Views
Posts: 277
Topic starter
(@blake-l)
Reputable Member
Joined: 19 years ago
[#37756]

Most pixel controllers I've seen have a 5A fuse on the output. Assuming 80% for safety, that's 4A usable. Assuming .06A per 12V WS2811 pixel, that's ~66 pixels. Good so far? So why is it I see people talking about making it 100+ pixels (one up to 200!) in their testing before seeing the pink-ish white? I assume this means they are only running off the controller... 100 * .06 = 6A!!! I must be missing part of the equation.


20 Replies
Posts: 825
 DanJ
(@danj)
Prominent Member
Joined: 13 years ago

I'll make a guess that you will get responses that people use "power injection" that provides a parallel power path to pixels... Directly from your PSU usually to the "end" of the pixels...


Reply
Posts: 277
Topic starter
(@blake-l)
Reputable Member
Joined: 19 years ago

If it didn't come across, I was trying to rule out that concept.


Reply
duramadmax
Posts: 904
(@duramadmax)
Noble Member
Joined: 16 years ago

Also the amperage ratings are usually conservative and you can push up to 100 pixels. But by mathematical calculations, you are correct.


Reply
Posts: 825
 DanJ
(@danj)
Prominent Member
Joined: 13 years ago

Yepper. I missed the point..... I am planning to do power injection this year--my 1st time to do that. Because I plan to run 2 lengths of 5m strips off of some of my E682 outputs... So I did the math & stayed below 5A on each output... Now I have to buy a fused terminal block though... Always details to tend to!!!


Reply
Posts: 231
(@apollosmith)
Reputable Member
Joined: 12 years ago

This assumes that each pixel is using and getting the full .06 amps and 12v. By the time you consider the resistance, etc. the ones at the end of the line won't be getting that much, so cumulatively you won't be at 6 amps or probably even 5 amps through the fuse. The question is whether the lower amperage at the end of the line makes any difference. For most installations, it probably doesn't.


Reply
Posts: 277
Topic starter
(@blake-l)
Reputable Member
Joined: 19 years ago

So how do I determine the true number of pixels I can run?


Reply
Posts: 210
(@gadgetsmith)
Estimable Member
Joined: 13 years ago

I simply tried different combinations. I connected 5m of strips on an output, drove it to full white and measured voltage drop and the amps it drew. This is pretty easy to do with a basic multimeter. For me, I could see where the leds started to get pinkish, but that was okay as it was near where I planned to cut them at the 3m mark. When I cut them, losing the last 2m decreased the load and all the pixels looked good.

I do this with all pixels that I buy. Don't trust specs if you want to know what is really going on.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
blake_l wrote:So how do I determine the true number of pixels I can run?

Your level of pink tolerance will determine the true # of pixels you can run . 🙂


Reply
Posts: 1049
(@phrog30)
Noble Member
Joined: 12 years ago

I did some testing the other day, 120 pixels full white was 4 amps, using amp clamp. The math is a good starting point, but sometimes real world is more precise. And, my controllers have a 5 amp fuse but are rated for 7 amp. For me, I noticed no pink at 120 pixels (2811).


Reply
Page 1 / 3
Share: