Pixel strip repair ...
 
Notifications
Clear all

Pixel strip repair question

12 Posts
3 Users
0 Reactions
3,598 Views
Posts: 1133
Topic starter
(@toozie21)
Noble Member
Joined: 19 years ago
[#38665]

I have one year old silicone tube style pixels on my matrix and I noticed yesterday that I have what appears to be a bad solder joint on one of them. I get stuck lights until I put some pressure on the built in solder joint between two of the strips (pressure on the next WS2812 LED also fixes it). I am guessing a cold or cracked solder joint is the culprit.

So my question is, do I try to cut open at the source, touch up the solder joints and reseal with silicone and clear heatshrink. Or should I open the sleeve up at an end and try to slide the strip out and back in?


11 Replies
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

I would cut a slit, just big enough to solder, fix, then reseal with silicone. Heat shrink not very effective on shapes that can change.


Reply
Posts: 1133
Topic starter
(@toozie21)
Noble Member
Joined: 19 years ago

The good news is that these are permanently mounted on a backing, so they don't flex or get moved ever.

I wonder how big of a slit I will need though so I don't melt anything. Have you ever had issues with the solder joints connecting the internal strips?


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

I still like silicone sealant - don't like round heat shrink on square material...maybe do both.
I have, and successfully fixed. Slit an L shaped hole - held flap back with alligator clip - Heated he solder soldered, then held it tightly compressed with a toothpick. Solder reseated and all was fine.

Another broken solder joint pulled the solder tab off one side. Re-soldering just wasn't going to happen. Being the positive lead was the only problem. I needed to tap the good connection, then run it down to the next joint and solder a tap there. Since it was a power or the ground lead, it will back feed to the skipped pixel. However if it is the DATA circuit, you can not back feed Can't back feed. data.

On another non repairable solder joint - bad DATA tab - just couldn't solder joint. I remover and replace a 3-led strip - three new solder joints each end.


Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 20 years ago

I open both ends of the ribbon. Then I solder a length of ribbon wire to the end opposite of the damaged or failed section. Have someone hold the pixel ribbon and slide the cover onto the ribbon wire until the damage is exposed. Repair it and slide the cover back onto the pixel ribbon.

Every time I cut a cover in the past, it leaked.

Jeff


Reply
Posts: 1133
Topic starter
(@toozie21)
Noble Member
Joined: 19 years ago
Jeff Millard wrote:I open both ends of the ribbon. Then I solder a length of ribbon wire to the end opposite of the damaged or failed section. Have someone hold the pixel ribbon and slide the cover onto the ribbon wire until the damage is exposed. Repair it and slide the cover back onto the pixel ribbon.

Every time I cut a cover in the past, it leaked.

Jeff

Jeff, what do you mean by ribbon wire? And are you just soldering the the three pads, they don't lift when you start to pull?

Short and badly typed since written from my phone...


Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 20 years ago

You can get bulk multi conductor ribbon wire from eBay et al, similar to the wire found on bullet pixel strings. Yes, I solder it to the pads. No, it it doesn't damage the pads in any way. In the years I've been using ribbon, I would guess I've removed pixel tape from silicone casing between 50 and 100 times. Mainly because I bought the pixel ribbon and case separately in bulk, and assembled it all myself. 5 meter pre assembled ribbon was useless to me. There isn't anything in my display 5 meters long. I've found that it becomes too difficult to manipulate when you get to about 20'. It's still possible, but difficult.

I was very surprised and relieved to find how easy it was to do this. You need to be confident with your soldering and gentle when sliding the silicone cover. Watch to make sure it doesn't bunch up as that is when it will tear of cause tiny holes. As long as you keep the ribbon wire and pixel tape straight, and evenly slide the entire cover (it will stretch a little and that's ok) by pulling it near the wire end and the middle at the same time, onto the wire.

Jeff


Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 20 years ago

Jason,

Empty some of your PM inbox and drop me a message please...

Jeff


Reply
Posts: 1133
Topic starter
(@toozie21)
Noble Member
Joined: 19 years ago
Jeff Millard wrote:Jason,

Empty some of your PM inbox and drop me a message please...

Jeff

Jeff, I did, but your box is full now 🙂


Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 20 years ago

I just saw that... Sorry.

Jeff


Reply
Page 1 / 2
Share: