Notifications
Clear all

Pixel errors ?

27 Posts
7 Users
0 Reactions
13.7 K Views
Posts: 241
(@mrdudeman)
Reputable Member
Joined: 12 years ago

dont use a test pattern when measuring just all on full white

you have the grounds of your 2 PS's tied together right?

and your +5v are seperated?


Reply
Posts: 33
Topic starter
(@humbug)
Eminent Member
Joined: 8 years ago
MrDudeMan wrote:dont use a test pattern when measuring just all on full white

you have the grounds of your 2 PS's tied together right?

and your +5v are seperated?

On the right tree I used 2 PS (for testing purposes) where the ground was tied together.
Usually each tree has one PS which are not tied together.

+5v is seperated, yes


Reply
Posts: 241
(@mrdudeman)
Reputable Member
Joined: 12 years ago

do you have a voltmeter?

how are you doing power injection?


Reply
Posts: 33
Topic starter
(@humbug)
Eminent Member
Joined: 8 years ago

I inject each 50 pixels from PS directly. Perhaps my clips are the issue. (Which run on left tree without any issues)

I think I gonna do two things.
To exclude my little controller is the issue, I gonna run the right tree separately.

Depending on the results, I will measure the voltage on full white, as you said.

Hope it brings light into darkness

Gesendet von iPhone mit Tapatalk


Reply
Posts: 33
Topic starter
(@humbug)
Eminent Member
Joined: 8 years ago

So, I found some time to test things.

It's not my little teensy, it seems to be power supply.

I re-wired everything from scratch again, still the same issue.
Again, I added a second PS, same issue.

I checked power voltage at last pixel which is about 4v. The rest is about 5.11V

Then I randomly removed one string from PS (ground and Data) and I got less pixel errors.
I removed a second one and get even better picture. At least I removed 3 random Strings from PS and issues are almost gone.
I get a full white on a static element, on tree and on my globe.

Pixel act kinda the have too much power or if the work well with less power.

I'm about to give up, no idea what to do now. Can't explain that issue.
Errors are almost gone, but it can’t be the solution to remove strings when u always need to inject power each 50 pixel.


Reply
Posts: 33
Topic starter
(@humbug)
Eminent Member
Joined: 8 years ago

So, I found some time to test things.

It's not my little teensy, it seems to be power supply.

I re-wired everything from scratch again, still the same issue.
Again, I added a second PS, same issue.

I checked power voltage at last pixel which is about 4v. The rest is about 5.11V

Then I randomly removed one string from PS (ground and Data) and I got less pixel errors.
I removed a second one and get even better picture. At least I removed 3 random Strings from PS and issues are almost gone.
I get a full white on a static element, on tree and on my globe.

Pixel act kinda the have too much power or if the work well with less power.

I'm about to give up, no idea what to do now. Can't explain that issue.
Errors are almost gone, but it can’t be the solution to remove strings when u always need to inject power each 50 pixel.

Another effect with oixel issues:

By removing 3 random strings from PS injection, i can reduce this issue to a minimum.


Reply
Posts: 241
(@mrdudeman)
Reputable Member
Joined: 12 years ago

sounds like u need 1.5 supplies per tree.
u sure when u inject power from 2nd supply that the +5v from it does not have a connection to the first +5v? you disconnect the +5 from the previous pixel/previous supply and have a new start for the 2nd +5v ?

hard to explain that in words, hope i made sense


Reply
Posts: 33
Topic starter
(@humbug)
Eminent Member
Joined: 8 years ago
MrDudeMan wrote:sounds like u need 1.5 supplies per tree.
u sure when u inject power from 2nd supply that the +5v from it does not have a connection to the first +5v? you disconnect the +5 from the previous pixel/previous supply and have a new start for the 2nd +5v ?

hard to explain that in words, hope i made sense

Not sure if I got your Point.
Both PS are tied with only ground. Not +5v. When I inject from 2nd PS I have a new start for a string with both ground and +5v.

Both trees are identical, same PS and same amount of pixels. I swapped boht PS, right tree always has issues.

BTW, here is another effect with lots of issues. By removing 3 random strings from PS injection, i can reduce this issue to a minimum.


Reply
Posts: 241
(@mrdudeman)
Reputable Member
Joined: 12 years ago

assuming u have 3 supplies
connect 2 supplies together with GND/(aka -5V not Earth)
use a thick wire that can carry at least 30A

first tree:
connect 66% of your pixels to PS1 +5v
connect 33% of your pixels to PS2 +5v

2nd tree:
connect 33% pixels to PS2 +5v
connect 66% pixels to PS3 +5v

if that dont work you might have a short or a bad pixel pulling too much current


Reply
Posts: 241
(@mrdudeman)
Reputable Member
Joined: 12 years ago

sorry. all 3 supplies gotta be connected with gnd


Reply
Page 2 / 3
Share: