Pixel Controllers.....
 
Notifications
Clear all

Pixel Controllers...HELP

22 Posts
11 Users
0 Reactions
6,482 Views
Posts: 11
Topic starter
(@kolar-kristmas)
Active Member
Joined: 10 years ago

Hi! Thank you for the quick response. I am so happy that others on this site have had experience with REnard and pixel controllers working in unison. I see that the Falcon is my best bet. As for going forward here is the things I am looking to purchase.
500 WS2811 Pixels
Raspberry Pi
Pixel controller??? Hopefully the FAlcon.

My only concern is that the controllers physically are able to link and communicate. I understand Vixen and how to program the sequences but I do not understand the communication part of the linking of controllers ie, Renard to Falcon (If i purchase that one). I also saw that there is a SanDevices board that looked fairly simple and has Renard Protocol


Reply
dpitts
Posts: 1020
(@dpitts)
Noble Member
Joined: 16 years ago

The F16V3 and F16V2/R all have 4 circuits of Renard output. The baudrate is configurable.


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

I use one output on a Sandevices 6804 to run my Renards. Once you have connection from 6804 to renard then you just Daisy chain all the other Renards. You may want to consider getting your Renards from WayneJ. He sells 8-16-24 channel Renards and his kits are awesome.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago

We would need to see pictures of the boards to know what is missing, it could just be the Triac or it could be the the Optoisolators and resistors too.

WayneJ is the creator of those boards and sell them as kits, so you may be able to get the parts from him, or using the BOM, order the parts from a supply house like Mouser

Kolar Kristmas wrote:Hi,
The renard controllers we have are REnard SS16 controllers. WE bought them off of someone on this website selling three of them but they weent fully equipped. Right now each board has only 8 outputs to each. Basically we need the parts to equip the second half of each controller up to 16 outputs or outlets.

Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
Kolar Kristmas wrote:Hi,
The renard controllers we have are REnard SS16 controllers. WE bought them off of someone on this website selling three of them but they weent fully equipped. Right now each board has only 8 outputs to each. Basically we need the parts to equip the second half of each controller up to 16 outputs or outlets.

Since I'm fairly sure you bought these from me, I can tell you that you won't need everything. PICs,resistors and Sockets for ALL channels are already on the board are on the board. You need 8 Triacs, 8 Optos and 8 Screw Terminals for each controller you have.

I don't think Wayne sells parts outside of the kits, but you can definitely get them easily from Mouser...

TRIACS: 511-BTA06-600CW
MOC/Optos: 859-MOC3023
Screw Terminals: - 571-2828372


Reply
Posts: 11
Topic starter
(@kolar-kristmas)
Active Member
Joined: 10 years ago

I believe we did. They were in the green cases. Thank you again they worked fairly well last Christmas and we just would like to expand our show including all the channels on those boardsa nd the pixel control.


Reply
Posts: 11
Topic starter
(@kolar-kristmas)
Active Member
Joined: 10 years ago

As for output from something like a raspberry pi... cna you just run right out of the serial port?

Here is my visual at least from what you are saying..

Raspberry Pi------------->Falcon F16V3------->Renard SS16--->Renard SS16----->Renard SS16


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago

Like David says, the Falcon has multiple output that can be configured for Renard (or other protocols, each is independent), to connect you would just run a Cat5 cable from the RJ45 on the Falcon to the "In" RJ45 on the 1st SS16 (just like daisy chaining), and then daisy chain the rest or run each off its own port on the falcon. The falcon itself connect via ethernet (normal PC network, also a cat5 cable) to your show PC/Pi or network switch if you have multiple devices. I know David did not say it, but his phone # is on his website and you can call him anytime w/ questions or advice.

Raspberry Pi-----(Ethernet)------>Falcon F16V3----(Serial)----->Renard SS16--->Renard SS16----->Renard SS16

Kolar Kristmas wrote:Hi! Thank you for the quick response. I am so happy that others on this site have had experience with REnard and pixel controllers working in unison. I see that the Falcon is my best bet. As for going forward here is the things I am looking to purchase.
500 WS2811 Pixels
Raspberry Pi
Pixel controller??? Hopefully the FAlcon.

My only concern is that the controllers physically are able to link and communicate. I understand Vixen and how to program the sequences but I do not understand the communication part of the linking of controllers ie, Renard to Falcon (If i purchase that one). I also saw that there is a SanDevices board that looked fairly simple and has Renard Protocol


Reply
Posts: 11
Topic starter
(@kolar-kristmas)
Active Member
Joined: 10 years ago

Perfect. Thank you guys so much for the help!


Reply
Posts: 401
(@kensington)
Reputable Member
Joined: 11 years ago
Reply
Page 2 / 3
Share: